ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)
Tex

สร้างโดย

Tex

3. พฤศจิกายน 2026FO
10
0
0
0
0

Hearing Protection (Ear Defenders): Rigid Cups on Liquid-Filled Cushions (Shaw & Thiessen, NRC, US 2,801,423, 1957)

Ear muffs that seal well and still stop low-pitched noise. Each ear is covered by a rigid cup on a cushion made of a thin PVC tube, emptied of air and part-filled with liquid. Pressed on, the liquid flows round the whole rim and fits the cushion to the head, yet cannot compress, so the cup does not vibrate as a whole and pass the sound in. A sprung headband with a pad holds the cups on ball joints. Result: circumaural ear defenders effective against low-frequency noise. Source: E. A. G. Shaw and G. J. Thiessen (National Research Council of Canada), US 2,801,423 (1957). Unknown: sizes and the attenuation achieved. Picture: the patent drawing.
ระดับกลาง
Unknown

คำแนะนำ

1

Make the cups

Make two rigid, non-porous cups to go over the ears, of wood, a hard plastic or a light metal such as aluminium. Widen each rim to about the width of the cushion, and make a small hole in the rim for the cushion's filling nipple. Fix a ball joint on the back of each cup. Not given: sizes.

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ2 ถ้วย
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ2 ball joints

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Make the liquid cushions

For each cup make an endless tube of thin, pliable but non-stretching plasticised PVC, 0.005 to 0.01 in thick, with a filling nipple. Draw out almost all the air, then fill it with liquid to more than a quarter but well under the whole of its cross-section: enough to reach right round the rim when pressed, not so much that it cannot seal. Fix it on the rim with the nipple in the hole. Ours: water as the liquid. Not given: tube size.

วัสดุสำหรับขั้นตอนนี้:

แผ่นพีวีซีแผ่นพีวีซี1 thin plasticised PVC tube
น้ำน้ำ1 filling

เครื่องมือที่ต้องใช้:

ชุดกระบอกฉีดชุดกระบอกฉีด
3

Fit the headband and wear them

Make a resilient headband frame with a sponge-rubber pad at its middle and a wire loop at each end. Through each loop pass a threaded stub from the cup's ball joint, with a washer, and tighten with a wing nut. Put the cups over the ears: the cushions take the shape of the head and seal, while the cups stay still against the low-frequency sound. Ours: spring steel for the frame.

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กสปริงลวดเหล็กสปริง1 frame and loops
วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 sponge rubber pad
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ2 threaded stubs
แหวนรองแบนแหวนรองแบน2 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ2 ชิ้น

เครื่องมือที่ต้องใช้:

คีมปากกลมคีมปากกลม

วัสดุ

7

เครื่องมือที่จำเป็น

4

วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...