ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel.
A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring.
Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
ขั้นสูง
Unknown
คำแนะนำ
1
1
Read Hug
Read Hug
"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2
2
Build the stirrer base
Build the stirrer base
Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.
วัสดุสำหรับขั้นตอนนี้:
แผ่นอะลูมิเนียม1 housing
มอเตอร์ไฟฟ้า1 ชิ้น
ชุดแท่งแม่เหล็ก1 drive magnet
รีโอสแตต1 ชิ้น
สายไฟอ่อนพร้อมปลั๊ก1 ชิ้นเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ
วิธีขึ้นรูปที่ไม่ทราบ3
3
Make the radiation shield
Make the radiation shield
Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.
วัสดุสำหรับขั้นตอนนี้:
แผ่นสเตนเลส - 3041 shield and legs
เพลาเกลียว1 spindle
น็อตหกเหลี่ยม2 ชิ้นเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
สว่านแท่น
ชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียว
วิธีขึ้นรูปที่ไม่ทราบ4
4
Fit the relay magnet
Fit the relay magnet
Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.
วัสดุสำหรับขั้นตอนนี้:
ชุดแท่งแม่เหล็ก1 relay magnet, 1/4 x 1 x 1 3/4 in.
วัสดุที่ไม่ทราบ1 hub and strap
สกรูเกลียวมิล2 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ
สว่านแท่น
ชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียว5
5
Mount the supports
Mount the supports
Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.
วัสดุสำหรับขั้นตอนนี้:
แผ่นสเตนเลส - 3041 three supports
สกรูเกลียวมิล3 ชิ้น
วัสดุฉนวนที่ไม่ทราบ3 tubular spacersเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
สว่านแท่น
ชุดดอกสว่าน6
6
Fit the heater and top
Fit the heater and top
Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.
วัสดุสำหรับขั้นตอนนี้:
ตัวทำความร้อน1 ring heater
สายไฟอ่อนพร้อมปลั๊ก1 ชิ้น
น็อตหกเหลี่ยม2 ชิ้น
แผ่นอะลูมิเนียม1 heat sink
แผ่นอะลูมิเนียม1 top plate
สกรูเกลียวมิล3 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องมือขึ้นรูปโลหะด้วยการหมุน
เครื่องกลึงโลหะ
สว่านแท่น
ชุดดอกสว่านวัสดุ
13- 1 top plateตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 relay magnet, 1/4 x 1 x 1 3/4 in.ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 three supportsตัวยึดตำแหน่ง
- 1 spindleตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 1 hub and strapตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 3 tubular spacersตัวยึดตำแหน่ง
- 1 ring heaterตัวยึดตำแหน่ง
- 1 heat sinkตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
8- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
