ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)
A small electric jig saw for curved cuts. A long U-shaped frame holds a fine blade stretched between its two arms. The frame's back end hangs on an L-shaped leaf spring, and an eccentric on a motor shaft rocks its lower arm up and down, so the blade saws through a slot in the table while the spring flexes. A wing nut tensions the blade; sawdust falls into a box below.
Result: a compact motor-driven jig (scroll) saw.
Source: G. O. Heese, US 2,692,622 (1954). Unknown: materials, sizes, the motor and the stroke. Picture: the patent drawing.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Build the base and table
Build the base and table
Make a long flat base, wider at the front. Fasten a long upright support along it, its back end a separate upright strip. Across the wide front stand two walls with matching upright guide slots, carrying a level table that overhangs to the front with a slot for the blade. Under the overhang set a removable open box for sawdust. Not given: materials, sizes.
วัสดุสำหรับขั้นตอนนี้:
วัสดุที่ไม่ทราบ1 base, support, walls, table, box
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 fastenersเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
สว่านมือ
ขนาดที่ไม่ทราบ2
2
Make the C-frame and spring hinge
Make the C-frame and spring hinge
Make a U-shaped blade frame: an upper arm, a lower arm, and a back piece made in one with the lower arm and bolted to the upper. Fix the upright part of an L-shaped leaf spring to the support's back strip; its flat part goes into a slot in the frame's back piece and is held by the same bolt. The frame can now swing up and down on the spring, its lower arm running in the walls' guide slots under the table.
วัสดุสำหรับขั้นตอนนี้:
โลหะที่ไม่ทราบ1 frame arms and back
แหนบซ้อนแผ่น1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
น็อตหกเหลี่ยม1 ชิ้นเครื่องมือที่ต้องใช้:
ประแจเลื่อน3
3
Fit the motor and eccentric
Fit the motor and eccentric
Fix an electric motor on the wide front of the base with its shaft running across under the frame's lower arm. Put two bolts down through the lower arm, one each side of the shaft; on them hang a lower strip resting on nuts and an upper strip under the arm, with a coil spring on each bolt pushing the strips apart. Fix an eccentric on the motor shaft between the two strips: as it turns it rocks the frame. Not given: the motor, the throw.
วัสดุสำหรับขั้นตอนนี้:
มอเตอร์ไฟฟ้า1 ชิ้น
บุชเยื้องศูนย์1 eccentric
โลหะที่ไม่ทราบ1 two strips
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 two bolts
น็อตหกเหลี่ยม2 ชิ้น
ชุดสปริงกด1 two coil springsเครื่องมือที่ต้องใช้:
ประแจเลื่อน4
4
Fit the blade clamps and use it
Fit the blade clamps and use it
On the lower arm fix a strip with a forked end that hooks under the blade's lower pin. On the upper arm fit a bracket with a cross pin; an arm rocks on it, its forked front end over the blade's upper pin, its back end pulled down by a bolt with a wing nut. Add forked guide strips above and below the table. To fit a blade, loosen the wing nut, hook both pins and tighten the nut to stretch the blade straight. Switch on and feed the work across the table. Ours: a pinned coping-saw blade.
วัสดุสำหรับขั้นตอนนี้:
โลหะที่ไม่ทราบ1 clamp strips, bracket, arm, guides
น็อตปีกผีเสื้อ1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้น
ใบเลื่อยฉลุ1 pinned bladeเครื่องมือที่ต้องใช้:
ประแจเลื่อนวัสดุ
10- 1 base, support, walls, table, boxตัวยึดตำแหน่ง
- 1 two boltsตัวยึดตำแหน่ง
- 1 clamp strips, bracket, arm, guidesตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 eccentricตัวยึดตำแหน่ง
- 1 two coil springsตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 pinned bladeตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



