ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings
Woody

สร้างโดย

Woody

9. พฤศจิกายน 2026NO
13
0
0
0
0

Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings

William Kelly of Hastings, Michigan, received US 24,127, dated 24 May 1859, for a vibrating churn. The tub hangs by straps from studs on a frame and is swung by its handles. A slide partition divides it in two; a dasher is hinged to each side of the partition, and a rod from each dasher's middle hooks onto the still frame. As the tub swings, the rods make the dashers flap, driving the cream against the partition and through openings at its foot from one side to the other. Holes in the dashers, and channels down through the partition, let air into the cream. This rung builds it with a 20-litre bucket hung on its side in a timber frame.
ระดับกลาง
About 1 day, plus printing

คำแนะนำ

1

How the dashers flap

กำลังโหลดสมุด Jupyter…
2

Swinging to work two dashers, before it

Merrill swung a pendulum beside the churn. Kelly swings the tub itself, and the still frame works the dashers.
3

Read US 24,127

"... as the dasher draws near the partition, the space is vacated by the cream passing out through the openings h h h in the partition D alternately from one apartment to the other."
4

Print the guide

A groove for the partition's edge. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
ไฟล์แบบSTLCC0 - Free
5

Print the box f

A journal box for a dasher. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
ไฟล์แบบSTLCC0 - Free
6

Frame

From 40 x 40 mm timber cut two rails A 640 mm long, four legs splayed from 150 mm either side of a rail's middle to 360 mm out at the floor, and two stretchers 440 mm long. Screw the legs to the rails' ends so the rails stand 580-620 mm up, 480 mm apart, and screw the stretchers between the leg pairs 130 mm up. Screw two cross pieces B 520 x 40 x 30 mm across the rails' tops 220 mm apart, and an eye bolt (staple g) under each at its middle. Put an M12 bolt through each rail's middle, pointing in, as the studs c.

วัสดุสำหรับขั้นตอนนี้:

ไม้เนื้ออ่อน 70x70 มม.ไม้เนื้ออ่อน 70x70 มม.4 ชิ้น
สกรูไม้ #10 x 3"สกรูไม้ #10 x 3"24 ชิ้น
สลักเกลียวหัวห่วงสลักเกลียวหัวห่วง2 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น
แหวนรองแบนแหวนรองแบน4 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ประแจเลื่อนประแจเลื่อน
ตลับเมตรตลับเมตร
7

Tub C and cover I

Lay a food-grade 20-litre bucket on its side, its lid snapped on. Cut away its wall above a level 100 mm over its axis to open the top, and file the edge smooth. Screw a flat-bar strap 30 x 6 mm to the middle of the bottom and of the lid, rising to 180 mm above the axis, each drilled 13 mm at the top to hook on a stud. Glue a guide upright in the middle of the bottom and of the lid, inside. Screw a hardwood foot G under the bucket and a hardwood handle H on each side at axis height. Cut a plywood cover I 340 x 250 mm with a slot 78 x 24 mm each side of the middle.

วัสดุสำหรับขั้นตอนนี้:

ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล8 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน8 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูไม้สกรูไม้6 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดไขควงชุดไขควง
8

Partition D and dashers E

Glue up a hardwood partition D 356 x 231 x 20 mm. Cut three half-round openings h 36 mm across in its foot, 100 mm apart, and drill an 8 mm channel j down from the top edge into each. Screw two journal boxes f on each face 113 mm above the foot, 160 mm apart. Cut two dashers E 100 x 220 mm from 10 mm plywood, drill each with four 24 mm holes i, glue an 8 mm dowel 200 mm long along one long edge as the journal, and glue a small block on top 50 mm from that edge for the rod's hook. Snap the journals into the boxes and slide the partition into its guides.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล8 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
กระดาษทรายกระดาษทราย
ชุดไขควงชุดไขควง
9

Hang it and fit the rods

Hook the straps over the studs so the tub hangs between the rails. Bend two 6 mm stainless rods with a hook at each end, 224 mm between hooks; put the cover on, pass a rod down each slot and hook it through the dasher's block below and the eye bolt above.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
10

The build in 3D

FreeCAD model of this build, the front half cut away: the frame with its studs, cross pieces and eye bolts, the bucket hung on its straps, the cover, the partition in its guides with its foot openings, the two hinged dashers and their rods. It was checked at five swing angles from -15 to +15 degrees.
ไฟล์แบบBLENDCC0 - Free
11

Churn

Lift the cover, pour about 8 litres of heavy cream at about 15 °C into the two halves, checked with the thermometer, and put the cover back over the rods. Take a handle and swing the tub steadily about 15 degrees each way; time it. When the butter comes, unhook the rods, lift out the partition and dashers, unhook the tub, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
12

Troubleshooting

Swinging-tub churn troubleshooting.

Flow

Loading...
13

History and honest limits

**William Kelly** of Hastings, Barry County, Michigan, US 24,127, 24 May 1859. He did not claim working dashers by the churn's swinging as such, only the dashers with the slide partition and rods so joined to the frame. His tub was made cylindrical below the centre and flat on two sides; ours is a bucket on its side. He gave no sizes: every size and material and the 15 degree swing are ours.

วัสดุ

19

เครื่องมือที่จำเป็น

18

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...