ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
Buttercup

สร้างโดย

Buttercup

10. พฤศจิกายน 2026IE
14
0
0
0
0

Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter

S. S. Langdon of Cleveland, Ohio, received US 25,126, dated 16 August 1859, for a rotary churn shaped like a common box. It turns on two journals in a frame. Inside, two zinc partitions set into saw kerfs make a cream chamber in the middle and two water chambers at the ends, for warm or cold water to temper the cream. A dash-frame of bars, held by a spring, sits midway while churning and is lowered to the bottom so the butter comes out without being pulled through it. Langdon gives no sizes; every size here is ours, and stainless steel stands in for his zinc.
ระดับกลาง
About 2 days

คำแนะนำ

1

How much cream, how much water

กำลังโหลดสมุด Jupyter…
2

A box churn tempered with water, before it

Langdon knew a box churn with water chambers had been used without a dasher. He added the dash-frame.
3

Read US 25,126

"When churning, I place the dash-frame about midway from the top to the bottom of the churn, as shown in Fig. 2. When the operation of churning is completed the dash-frame may be lowered to the bottom of the churn in order to remove the butter without interfering with the latter or causing it to adhere to the dasher".
4

Box and kerfs

From 19 mm hardwood cut a bottom 440 x 278 mm, two sides 440 x 240 mm and two ends 240 x 240 mm. Saw a kerf 1 mm wide and 6 mm deep across each side and the bottom, 150.4 mm either side of the middle, for the partitions. Glue and screw the ends between the sides and the box onto the bottom, square.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้24 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยมือเลื่อยมือ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แคลมป์แบบบาร์แคลมป์แบบบาร์
ฉากตายฉากตาย
ตลับเมตรตลับเมตร
5

Partitions F and the water chambers E

Cut two stainless sheet plates 251 x 245 mm, 0.8 mm thick, and slide them down the kerfs: each closes off a water chamber 50 mm long at an end. Drill a 17 mm hole low in each end board and one in the bottom of the cream chamber, for the plugs. Fill the box with water overnight so the wood swells tight round the plates; check that each water chamber holds water without filling the cream chamber, then empty it.

วัสดุสำหรับขั้นตอนนี้:

แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
น้ำน้ำ
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
6

Print the plugs L

A tapered plug 18 mm at the head, 25 mm long. Print three. PETG, 0.2 mm layers, 100 % infill.
ไฟล์แบบSTLCC0 - Free
7

Dash-frame K and spring K'

Cut two hardwood rails 296 x 44 x 20 mm and seven bars 20 x 20 x 196 mm. Fix the bars between the rails set diamond-wise, one corner up, as Fig. 2 draws, 37 mm apart, glued and screwed through the rails. Rivet or screw a bowed strip of stainless spring steel, 256 mm long, along the outside of one rail so it presses on the side and holds the frame wherever you set it.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แถบเหล็กกล้าไร้สนิมรีดเย็น (420)แถบเหล็กกล้าไร้สนิมรีดเย็น (420)1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้14 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยมือเลื่อยมือ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
8

Cover G, journals B, frame A and crank C

Cut the cover from 12 mm plywood to the box's outside size. Set four 6 mm bolts head down in the sides' top edges, 75 mm either side of the middle, through matching holes in the cover, with wing nuts on top. Glue and screw a hardwood block 80 x 80 x 40 mm to the middle of each end, bore it 20 mm, drive in a 20 mm steel stub and pin it with a bolt across. Build a pine frame on four posts with open slots in its top rails for the stubs, and a crank with a turned handle on one stub outside the frame.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้อัดแผ่นไม้อัด1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด6 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ4 ชิ้น
แหวนรองแบนแหวนรองแบน4 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน2 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เหล็กกล้าแท่งดิบเหล็กกล้าแท่งดิบ1 ชิ้น
ไม้เนื้ออ่อน 70x70 มม.ไม้เนื้ออ่อน 70x70 มม.2 ชิ้น
แผ่นไม้สนแผ่นไม้สน1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้24 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ประแจเลื่อนประแจเลื่อน
ฉากตายฉากตาย
ตลับเมตรตลับเมตร
9

The build in 3D

FreeCAD model of this build, cover and one side cut away: the cream chamber between the stainless partitions, the water chambers at the ends with their plugs, the dash-frame of diamond-set bars midway, the journal blocks, the frame and the crank. The box was turned through 16 angles in the frame.
ไฟล์แบบBLENDCC0 - Free
10

Temper and churn

Fill both water chambers with warm or cold water as needed, checked with the thermometer, and plug them. Set the dash-frame midway, pour in about 5 litres of heavy cream, bolt the cover on and turn the crank steadily, timing it. When the butter comes, take the cover off, push the dash-frame down to the bottom, lift the butter out over it and drain the buttermilk at the bottom plug. Wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด5 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
กาต้มน้ำไฟฟ้ากาต้มน้ำไฟฟ้า
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
11

Troubleshooting

Water-chamber churn troubleshooting.

Flow

Loading...
12

History and honest limits

**S. S. Langdon** of Cleveland, Ohio, US 25,126, 16 August 1859, "Churn". He claimed his construction and arrangement of rotary churns with the dash-frame K and the water chambers E. He gives no sizes, so every size here is ours. Stainless steel replaces his sheet zinc because the cream and buttermilk touch the partitions; four wing-nut bolts are his "thumb screws placed on the edge of the cover"; the spring strip and the journal blocks are our versions of his spring K' and journals B.

วัสดุ

17

เครื่องมือที่จำเป็น

19

ไฟล์ออกแบบ

2

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...