ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
12
0
0
0
0

Lead Came: Window Rods Cast in a Split Wooden Mould (Theophilus, tr. Hendrie 1847)

Theophilus' way to cast window leads without an iron mould: a stick of fir is split, a groove marked with a red-dyed flax thread and cut along both halves, the halves bound with a strap and the lead poured in again and again until the hot lead has burnt the groove to the bottom. Each rod is then trimmed in a slotted wooden gauge, cut with a knife on both sides and scraped smooth. Source: Theophilus, De Diversis Artibus, Book II, ch. XXVI, tr. R. Hendrie (1847), pp. 149-151. Picture: p. 151.
ระดับกลาง
Unknown

คำแนะนำ

1

Split and mark the wood

Take fir or another wood that splits smoothly, the size of the iron mould (a yard long, two fingers broad, a finger thick). Split it and round the outside. Mark each end of both pieces for the width of the rod. Stretch a thin twisted flax thread wet with red colour from mark to mark on one inner face and press the other piece against it, so the line shows on both; do the same for the second line.

เครื่องมือที่ต้องใช้:

แม่พิมพ์ตะกั่วกรอบกระจกแม่พิมพ์ตะกั่วกรอบกระจก
ด้ายลินินด้ายลินิน
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
2

Cut the groove

Cut the groove between the lines with a knife, as wide and deep as you wish, but not through the lower end; leave an opening at the top for pouring.

เครื่องมือที่ต้องใช้:

มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
แม่พิมพ์ตะกั่วกรอบกระจกแม่พิมพ์ตะกั่วกรอบกระจก
3

Cast the rods

Melt the lead as for the iron mould. Bind the two halves together with a strap from top to bottom, hold the mould with a wooden holder and pour in the lead; loosen the strap and take out the rod. Bind and cast again until the burning reaches the bottom of the groove; after that you can cast gently as many as you wish.

วัสดุสำหรับขั้นตอนนี้:

แท่งตะกั่วแท่งตะกั่ว1 pure lead

เครื่องมือที่ต้องใช้:

แม่พิมพ์ตะกั่วกรอบกระจกแม่พิมพ์ตะกั่วกรอบกระจก
สายหนังสายหนัง
หม้อดินหม้อดิน
ถ่านไม้ถ่านไม้
ทัพพีทัพพี
4

Trim the rods

Cut a piece of wood two fingers wide and as thick as the inside of the groove, split in the middle at one end so the rod fits into the slit. With the rod in it, cut it with a knife on both sides, then smooth and scrape it as you like.

เครื่องมือที่ต้องใช้:

มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์

วัสดุ

1
  • ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

7

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...