ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
12
0
0
0
0

Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)

Simon Lutsker of Shaker Heights, Ohio, received US 2,870,536, dated 27 January 1959, for a tubing cutter that grips small and large tubes equally well. The wheel turns under a housing at the foot of a guide. A block slides up the guide on a screw. Two arms hang from the block, each with a roller at its lower end. Springs press the arms' curved cam edges against rollers on the housing. As the screw draws the block up, the arms swing inwards or outwards, so the wheel and the two rollers stay about evenly spaced round the tube, whatever its size. We worked out the cam so the three contacts are exactly 120 degrees apart. The curve comes out as an arc, as in his patent. All sizes are ours.
ขั้นสูง
About 4 days

คำแนะนำ

1

Three points evenly round

กำลังโหลดสมุด Jupyter…
2

Read US 2,870,536

"Irrespective of the size of the tubing which is being cut, the points of engagement of the cutter wheel 21 and support rollers 32 with the tubing will always be substantially equidistant from each other circumferentially of the tubing."
3

Print the template

The arm plate with its cam edge, the housing and the guide block at 1:1, with holes, slots and sizes. print at 100 % (check the 50 mm bar).
ไฟล์แบบPDFCC0 - Free
4

Cut the arm plates

Glue four copies of the arm outline on 3 mm steel plate. Saw and file them to the line, taking the cam edge slowly and checking it against the template. Clamp them in a stack and drill the 4 mm pivot and roller-pin holes and the two 3 mm holes through all four together.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
ชุดตะไบเข็มชุดตะไบเข็ม
สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานของเครื่องปากกาจับชิ้นงานของเครื่อง
ชุดดอกสว่านชุดดอกสว่าน
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
5

Make the housing

From 30 x 20 flat bar, saw a block 64 mm long and file it to 28 x 18 mm, leaving the two ears below its middle. Saw the forked ends: two cuts 14.4 mm apart, 20 mm in from each end, and break out the middle. Saw and file a 7 mm slot up between the ears for the wheel. Drill the 5 mm shaft hole across the ears, the 4 mm housing-roller pins across the forks, and the 4 mm rivet hole. File a groove 20 mm wide and 3 mm deep down each face for the guide's legs.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานของเครื่องปากกาจับชิ้นงานของเครื่อง
ชุดดอกสว่านชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
เหล็กขีดเหล็กขีด
6

Make the block and the guide

Saw the guide block from the same bar, 60 x 18 x 28 mm, with forked ends from 14 mm out, the 4 mm pivot holes, the 3 mm spring-pin holes and the leg grooves. Drill 8.5 mm up its middle and tap M10. Bend a 20 x 3 mm flat bar into an inverted U with its legs 22 mm apart inside and 69 mm high, and drill a 10.5 mm hole in its top.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน2 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานของเครื่องปากกาจับชิ้นงานของเครื่อง
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ค้อนหัวกลมค้อนหัวกลม
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
7

Turn the rollers and the wheel shaft

Turn two housing rollers 10 mm across and 14 mm long, and two lower rollers 12 mm across and 7.6 mm long, from mild steel bar, all bored 4.2 mm. For the wheel shaft, turn a 6 mm rod to 5 mm, leaving a 6 mm head, file a flat on the head, and turn a groove near the other end.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำแท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
มีดตัดงานกลึงมีดตัดงานกลึง
ชุดดอกสว่านชุดดอกสว่าน
ชุดตะไบชุดตะไบ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าเครื่องมือแท่งเหล็กกล้าเครื่องมือ1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
มีดตัดงานกลึงมีดตัดงานกลึง
ชุดดอกสว่านนำศูนย์ชุดดอกสว่านนำศูนย์
ชุดดอกสว่านชุดดอกสว่าน
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
แม่เหล็กเล็กแม่เหล็กเล็ก
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
หินลับมีดหินลับมีด
ถุงมืองานเชื่อมถุงมืองานเชื่อม
แว่นนิรภัยแว่นนิรภัย
10

Make the springs

From spring steel strip, cut two strips 8 mm wide and 30 mm long for the arm springs, and one 6 mm wide and 25 mm long to hold the wheel shaft. Bend each arm spring so it presses on its arm's spring pin and pushes the arm outwards. Drill a hole in the end of each for its pin or screw.

วัสดุสำหรับขั้นตอนนี้:

แถบเหล็กสปริงแถบเหล็กสปริง1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
11

Make the screw

Cut 90 mm of M10 threaded rod. Lock two nuts together 25 mm from its top as the flange. Put it up through the guide's top hole, add two washers as the spacer, then a nut locked with a second one. Drill a 6 mm hole across the top end and fit a 70 mm piece of 6 mm rod as the T-handle.

วัสดุสำหรับขั้นตอนนี้:

เพลาเกลียวเพลาเกลียว1 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม4 ชิ้น
แหวนรองแบนแหวนรองแบน2 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำแท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

ประแจเลื่อนประแจเลื่อน
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ค้อนหัวกลมค้อนหัวกลม
12

Assemble

Pin each arm pair together with its lower roller between the plates, and with short tubes as spacers on the pivot and spacer pins. Pin the arms into the block's forked ends. Fit the housing rollers in the housing's forks and the wheel on its shaft, with the flat spring screwed to the housing and sitting in the shaft's groove. Screw the block onto the screw, feed the arms down through the housing's forks inside its rollers, and rivet the guide's legs into the housing's grooves. Pin the arm springs to the block. Oil every pin and the screw.

วัสดุสำหรับขั้นตอนนี้:

สลักเดือยเหล็กสลักเดือยเหล็ก8 ชิ้น
หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 ชิ้น
สกรูหัวจมหกเหลี่ยมสกรูหัวจมหกเหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนหัวกลมค้อนหัวกลม
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
น้ำมันตัดกลึงน้ำมันตัดกลึง
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Turn the handle to open the arms, put the cutter over the tube, and turn it back until the rollers lift the tube against the wheel. Check by eye that the wheel and rollers look evenly spaced. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองแดงท่อทองแดง1 ชิ้น

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เครื่องมือลบครีบเครื่องมือลบครีบ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
14

Troubleshooting

Cam-arm tubing cutter troubleshooting.

Flow

Loading...
15

History and honest limits

**Simon Lutsker** of Shaker Heights, Ohio, US 2,870,536, dated 27 January 1959, filed 26 August 1957. He claimed "a guide block mounted for movement along said guide member and movable by said screw means, a pair of cammable members pivotally secured to said guide block" and the springs pressing their "arcuate cam surfaces" against the housing rollers. He said the contacts stay "substantially" equidistant; ours are set exactly 120 degrees apart. The patent gives no sizes or cam radius; all of ours are ours.

วัสดุ

13

เครื่องมือที่จำเป็น

29

ไฟล์ออกแบบ

1

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...