ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Miniature Printing Electronic Calculator: Kilby, Merryman & Van Tassel, 1974
Ed

สร้างโดย

Ed

12. ตุลาคม 2026FI
18
0
0
0
0

Miniature Printing Electronic Calculator: Kilby, Merryman & Van Tassel, 1974

Jack S. Kilby, Jerry D. Merryman and James H. Van Tassel of Texas Instruments first filed for this portable calculator in 1967; the patent, US 3,819,921, was granted in 1974. It adds, subtracts, multiplies and divides. All the arithmetic and control is done by one integrated semiconductor circuit array lying flat under the keyboard encoder. Answers are printed by a thermal print head, a 3 × 5 array of heater elements on a semiconductor wafer, on heat-sensitive paper tape read through a magnifying window. The case measured 4¼ × 6⅛ × 1¾ inches and the calculator weighed 45 ounces, running on batteries.
ขั้นสูง
Factory process

คำแนะนำ

1

Keys and encoder

Mount the 18 keys (0–9, +, −, ×, ÷, the decimal point, C for clear, E for error and P for print) in stepped holes in the upper case. Each key shaft slides in a bearing; a helix spring under the shaft head returns it, guide pins stop it turning, and a resilient pad at its base carries a thin gold-plated copper strip. Below lies the encoder: conductive strips on an insulating board, grouped so each key shorts its own set of output terminals and encodes its digit in excess-3 binary code.

วัสดุสำหรับขั้นตอนนี้:

กล่องเครื่องคิดเลขสองส่วนแบบบานพับกล่องเครื่องคิดเลขสองส่วนแบบบานพับ1 ชิ้น
ปุ่มคืนตัวด้วยสปริงพร้อมแผ่นสัมผัสปุ่มคืนตัวด้วยสปริงพร้อมแผ่นสัมผัส18 ชิ้น
แผ่นวงจรเข้ารหัสแป้นพิมพ์แผ่นวงจรเข้ารหัสแป้นพิมพ์1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดคีมคีบละเอียดชุดคีมคีบละเอียด
ชุดไขควงชุดไขควง
2

Primary electronics

Mount the integrated circuit array below the encoder, in a plane parallel to it, and connect the encoder's terminals to it. The array holds the arithmetic and control sections, generating the timing signals for calculating, printing and advancing the tape.

วัสดุสำหรับขั้นตอนนี้:

แผงวงจรรวมของเครื่องคิดเลขแผงวงจรรวมของเครื่องคิดเลข1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดคีมคีบละเอียดชุดคีมคีบละเอียด
3

Printer and tape

Place the thermal print head above a resilient pressure pad, its wafer surface against the tape. Rest the tape reel on a shelf; the tape runs up through a guide block, over the pad under the print head, past the magnifying lens window and out through the side of the case. A solenoid tape-advance mechanism steps the tape on after each line: its coil pulls a pivoted clapper, a spring-biased clutch grips the tape against a clutch plate, and a drive spring pushes it forward when the coil releases. An insulating acrylic cover plate separates the shelf from the primary electronics.

วัสดุสำหรับขั้นตอนนี้:

หัวพิมพ์ความร้อนสารกึ่งตัวนำแบบรวมหัวพิมพ์ความร้อนสารกึ่งตัวนำแบบรวม1 ชิ้น
เทปกระดาษไวความร้อนเทปกระดาษไวความร้อน1 ชิ้น
กลไกเลื่อนเทปด้วยโซลินอยด์กลไกเลื่อนเทปด้วยโซลินอยด์1 ชิ้น
หน้าต่างเลนส์ขยายหน้าต่างเลนส์ขยาย1 ชิ้น
แผ่นอะคริลิกแผ่นอะคริลิก1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดคีมคีบละเอียดชุดคีมคีบละเอียด
ชุดไขควงชุดไขควง
4

Power

Fix the batteries, the auxiliary electronics module and the tape advance on the floor of the lower case. Three 1½ volt cells in series give 4½ volts and eight in series give 12 volts; the auxiliary module drives the tape-advance coil and the print timing. Wire the supply through the on/off switch to the primary electronics, and fit a battery charger plug in the wall of the lower case. Hinge and latch the two case halves so the top lifts for access.

วัสดุสำหรับขั้นตอนนี้:

ถ่านไฟฉาย (เซลล์แห้ง)ถ่านไฟฉาย (เซลล์แห้ง)11 ชิ้น
โมดูลอิเล็กทรอนิกส์เสริมโมดูลอิเล็กทรอนิกส์เสริม1 ชิ้น
สวิตช์เปิด/ปิดสวิตช์เปิด/ปิด1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมปอกสายไฟคีมปอกสายไฟ
คีมปากจิ้งจกคีมปากจิ้งจก
ชุดไขควงชุดไขควง

วัสดุ

12

เครื่องมือที่จำเป็น

4

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...