ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
Jehu Mitchell of Aleppo township, Pennsylvania, received US 27,927, dated 17 April 1860, for a churn. The dasher hangs from above in a long journal box on a standard fixed to the lid, with no step or metal bearing in the tub, whose "oxidation ... imparts a bad flavor to the butter". One half of the box is a cap hinged at one side: lift out half the lid, unhook the cap and the dasher comes out with the gearing left in place.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days, plus printing
คำแนะนำ
1
1
Held from above
Held from above
กำลังโหลดสมุด Jupyter…
2
2
A crank-turned upright dasher, one week before
A crank-turned upright dasher, one week before
Lynch's shaft stands in a step on the bottom. Mitchell hangs his from above, with nothing in the tub.
3
3
Read US 27,927
Read US 27,927
"Suspending the dasher within an elongated hinged journal box in the manner described, combined the following advantages. A rigid bearing is afforded to the dasher so as to prevent any tremulous motion, without the necessity of any metallic step or bearing within the churn, the oxidation of which imparts a bad flavor to the butter."
4
4
Print the driving wheel E
Print the driving wheel E
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion M
Print the pinion M
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Lid B and C, brakes O
Lid B and C, brakes O
Cut a hardwood lid 15 mm thick to sit on the bucket's rim and saw it in two across the middle: part C carries the standard, part B lifts out. Cut a 28 mm half-hole in the middle of the cut edge for the shaft and a 30 mm hole in B to look in. Screw three hardwood brakes O, 30 mm deep and 245 tall, to the bucket's side a third of a turn apart, and seal the screw holes outside with silicone.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แผ่นไม้เนื้อแข็ง2 ชิ้น
สกรูไม้6 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
เลื่อยวงเดือนตั้งโต๊ะ
ชุดดอกสว่านใบพาย
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง
ตลับเมตร7
7
Standard D, journal box and cap G
Standard D, journal box and cap G
Glue up a hardwood standard 60 mm wide and 66 deep, 111 mm tall above the lid, with its back 22 mm rising to 217 mm and bored 12.6 mm across near the top for the wheel's axle. Mortise it into lid part C behind the shaft's hole. Cut a cap G 60 x 30 mm, 111 tall, and bore a 25.2 mm hole down the joint between standard and cap, half in each. Hang the cap on a butt hinge at one side and fit a hook H and eye I on the other.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
บานพับตู้1 ชิ้น
ตะขอและห่วงติดเสื้อผ้า1 ชิ้น
สกรูไม้4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
แคลมป์แบบบาร์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
ชุดไขควง8
8
Dasher J with wings N and collars K and L
Dasher J with wings N and collars K and L
Cut a 25 mm hardwood dowel 485 mm long and glue a 12 mm stainless spindle into its top, standing 56 mm out. Glue two hardwood wings 200 x 60 x 20 mm across it, 20 and 140 mm above its foot, each bored with two 24 mm holes. Fit a hardwood collar L 44 mm across just below the lid, and a collar K 40 mm across on the spindle resting on the box's top. Set the shaft in the box, close the cap, and key the pinion M on the spindle above K.
วัสดุสำหรับขั้นตอนนี้:
เดือยไม้เนื้อแข็ง2 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส1 ชิ้น
กาวไม้1 ชิ้น
ท่อนไม้เนื้อแข็ง1 ชิ้น
Shaft Collar1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะ
ชุดดอกสว่านใบพาย
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
กระดาษทราย9
9
Driving wheel E and crank
Driving wheel E and crank
Pass a 12 mm stainless axle through the standard's back, fit the wheel E on it meshing the pinion, and a hardwood crank with a dowel handle on the other end; hold it with a collar and split pin.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
Shaft Collar1 ชิ้น
สลักผ่า1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะ10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the dasher J with its two wings hanging from the journal box, the brakes O, the lid, the standard D with its hinged cap G, hook and eye, and the wheel E with pinion M.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the lid and dasher in place, and turn the crank steadily, timing it. To look at the butter, lift out lid part B. When the butter comes, lift part B out, unhook the cap and take the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด8 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่12
12
Troubleshooting
Troubleshooting
Hung-dasher churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Jehu Mitchell** of Aleppo township, Greene County, Pennsylvania, US 27,927, 17 April 1860, "Churn". He did not claim a churn without a bottom step nor a hinged bearing alone, but the gearing, standard, hinged cap, dasher and collar together. His journal box runs higher; ours stops below the crown wheel. His wings and brakes are "of common construction"; our two wings and three brakes, and every size, are ours.
วัสดุ
16- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 10 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
18- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Leaning-Scoop Churn: Three Scoops Tilted 10, 5 and 0 Degrees Throw the Cream at Sharp-Topped Ribs and a Slit Cover
โดย Buttercup
งานไม้
10
0
0
0
0
0

Floating-Breaker Churn: A Propeller Dasher Under a Breaker That Floats in Wall Grooves, a Water Tube Held by the Faucet
โดย Buttercup
งานไม้
8
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

