ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
ระดับกลาง
About an hour per bolt
คำแนะนำ
1
1
Choosing the hole
Choosing the hole
กำลังโหลดสมุด Jupyter…
2
2
Read Mechanick Exercises
Read Mechanick Exercises
"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3
3
Forge the square neck
Forge the square neck
Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.
วัสดุสำหรับขั้นตอนนี้:
แท่งเหล็กดัด1 ชิ้นเครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
ค้อน
คีมช่างตีเหล็ก4
4
Round the pin, cut the head
Round the pin, cut the head
Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
สกัดตัดบนทั่ง
คีมช่างตีเหล็ก
ปากกาจับชิ้นงานหนัก
ค้อน5
5
Punch the nut
Punch the nut
Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.
วัสดุสำหรับขั้นตอนนี้:
แท่งเหล็กดัด1 ชิ้นเครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
ทั่ง
เหล็กตอกร้อน
ค้อน
ถังชุบน้ำ
คีมช่างตีเหล็ก6
6
Thread the pin
Thread the pin
File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.
เครื่องมือที่ต้องใช้:
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหนัก
ชุดต๊าปและดายทำเกลียว7
7
Tap the nut
Tap the nut
Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.
เครื่องมือที่ต้องใช้:
ปากกาจับชิ้นงานหนัก
ชุดต๊าปและดายทำเกลียว8
8
Troubleshooting
Troubleshooting
Screw bolt troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.
วัสดุ
1- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
10- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

