ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
อนาคตสีเขียว
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments
Clay

สร้างโดย

Clay

25. พฤษภาคม 2026DK
0
0
0
0
0

Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments

Clay beads are among the oldest decorative objects made by humans — fired clay beads from Dolní Věstonice in the Czech Republic date to approximately 26,000 years ago, making them some of the earliest known ceramics. Unlike shell or bone beads that require drilling through hard material, clay beads are formed soft and pierced with a stick before firing, making them far easier to produce in quantity. Beads served as personal ornament, trade goods, counting tokens, and markers of social status across all prehistoric cultures. The process is simple: prepare clay, roll beads, pierce holes, dry, fire. The key challenge is preventing the beads from cracking during drying and firing — uniform thickness, thorough drying, and slow temperature increase are essential.
เริ่มต้น
2-3 hours (plus firing)

คำแนะนำ

1

Gather and Clean the Clay

Gather fine-grained clay and remove stones, roots, and debris by hand.

วัสดุสำหรับขั้นตอนนี้:

Raw Clay from RiverbankRaw Clay from Riverbank1 ชิ้น
2

Knead the Clay Thoroughly

Knead the clay thoroughly to remove air bubbles — wedging on a flat stone works well.
3

Add Temper (Optional)

Optionally mix in a small amount of fine sand (10-15%) as temper to reduce cracking.
4

Roll the Beads

Pinch off a small piece of clay and roll it between your palms into a smooth sphere (8-15mm diameter).
5

Pierce the Centre Hole

Pierce the centre of each bead with a thin stick, twig, or bone awl — push through from one side, then ream from both sides.

เครื่องมือที่ต้องใช้:

Bone AwlBone Awl
6

Size the Hole for Cordage

The hole should be large enough for a cord (2-3mm diameter).
7

Leave the Stick in During Drying

Leave the stick in place while drying to keep the hole open and prevent it from closing.
8

Dry Slowly in Shade

Set beads on a dry surface in shade and dry slowly for 2-3 days — fast drying causes cracks.
9

Remove the Sticks

Remove the sticks once the clay is leather-hard.
10

Add Surface Decoration (Optional)

Optional: press patterns into the bead surface with a pointed stick or stamp with cord impressions before drying.
11

Fire in a Pit Kiln

Fire the beads in a pit kiln: place in the coals, cover with fuel, burn for 2-3 hours at 600-800°C, and allow to cool slowly in the ash.

วัสดุ

1

เครื่องมือที่จำเป็น

1
  • ตัวยึดตำแหน่ง

วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...