ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
PTFE Sheet: Compact-Extruded Films, Sintered, Laid at 45° and Fused (MacFarland, Hills-McCanna, US 3,130,954)
Charlie

สร้างโดย

Charlie

31. ตุลาคม 2026DE
10
0
0
0
0

PTFE Sheet: Compact-Extruded Films, Sintered, Laid at 45° and Fused (MacFarland, Hills-McCanna, US 3,130,954)

Thick PTFE was cut from a sintered billet with a knife, and the skived sheet tore along the knife marks. MacFarland built his sheet up instead, from thin extruded films laid crosswise and fused together, for the liner of a valve diaphragm. Result: a dense PTFE sheet, about 7,000 psi tensile and 450 % elongation, much the same in every direction. Source: MacFarland, US 3,130,954 (Hills-McCanna, 1964). Not given: furnace temperature, mill pressure. Picture drawn by Youblob.
ขั้นสูง
Factory process

คำแนะนำ

1

Compact-extrude a film

Feed finely divided PTFE resin from a hopper through a screw extruder to a slot die, usually without added heat. It comes out as a compact film that holds together unsintered, up to 24 in wide.

วัสดุสำหรับขั้นตอนนี้:

ผงเรซิน PTFEผงเรซิน PTFE1 as required

เครื่องมือที่ต้องใช้:

เครื่องอัดรีดพลาสติกเครื่องอัดรีดพลาสติก
แม่พิมพ์อัดรีดแม่พิมพ์อัดรีด
2

Sinter and coin the film

Carry the film through a sintering furnace to its fusion (gel) state and coin it in a mill as it goes. It comes out dense, with few pores, 5-8 mils thick. Ours: muffle furnace and calender rolls.

เครื่องมือที่ต้องใช้:

เตาเผามัฟเฟิลเตาเผามัฟเฟิล
ลูกกลิ้งแคลนเดอร์ผิวเรียบลูกกลิ้งแคลนเดอร์ผิวเรียบ
3

Lay the films crosswise and fuse them

Each film is a little stronger lengthwise, so stack several with their lengthwise axes turned by the same angle each time; 45° works well (MacFarland shows five plies). Feed the stack into a final sintering and compacting mill to fuse it into one sheet (over 20 mils thick). Ours: muffle furnace and calender rolls.

เครื่องมือที่ต้องใช้:

เตาเผามัฟเฟิลเตาเผามัฟเฟิล
ลูกกลิ้งแคลนเดอร์ผิวเรียบลูกกลิ้งแคลนเดอร์ผิวเรียบ

วัสดุ

1
  • ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

4

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...