ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Razor Blades from a Continuous Steel Strip (Tarbox 1915)
J. P. Tarbox · Public domain (US patent)
Forge

สร้างโดย

Forge

27. ตุลาคม 2026NO
16
0
0
0
0

Razor Blades from a Continuous Steel Strip (Tarbox 1915)

Safety razor blades are made without ever cutting the steel into loose pieces first. A long strip, blade-wide and blade-thick, is punched and notched at every blade length. It then runs through grinding, hardening, tempering, edge grinding, stropping and wrapping, and only at the end is it snapped apart into blades. John Tarbox's machine even set the temper itself, with a selenium cell that watched the colour of the steel. Source: J. P. Tarbox, US 1,165,037 (1915). The patent gives no temperatures, steel grade or blade sizes. Picture: Tarbox's drawing of the whole line.
ขั้นสูง
Continuous line

คำแนะนำ

1

Punch and weaken the strip

Start from steel rolled into long strip as wide and as thick as the blade. Punch holes along it to suit the razor holder: a Gillette-type holder has three projections. At every blade length, weaken the strip by notching both edges, thinning it across, or punching a hole on the line.

วัสดุสำหรับขั้นตอนนี้:

แถบเหล็กกล้าคาร์บอนแถบเหล็กกล้าคาร์บอน1 strip

เครื่องมือที่ต้องใช้:

เครื่องปั๊มโลหะเครื่องปั๊มโลหะ
2

Rough-grind the faces

Feed the strip by its holes between a pair of grinding wheels, one on each side, to remove the surface irregularities.

เครื่องมือที่ต้องใช้:

ล้อเจียรล้อเจียร
3

Harden: heat and chill

Run it through an electric tunnel heater, then straight into a chilling bath of oil or water.

เครื่องมือที่ต้องใช้:

เตาเผาแบบท่อเตาเผาแบบท่อ
บ่อชุบด้วยน้ำมันบ่อชุบด้วยน้ำมัน
4

Rub off the oxide

Pass it between emery wheels to rub the oxide off the chilled strip, so its temper colour can be seen when it is reheated.

เครื่องมือที่ต้องใช้:

ล้อเจียรล้อเจียร
5

Temper to straw colour

Reheat it in a second, smaller tunnel heater and chill it again. Tarbox held the colour at the temper wanted, for example straw, by letting a selenium cell compare the strip with a coloured standard disk and adjust the heater.

เครื่องมือที่ต้องใช้:

เตาเผาแบบท่อเตาเผาแบบท่อ
บ่อชุบด้วยน้ำมันบ่อชุบด้วยน้ำมัน
6

Grind and strop the edges

Grind both edges at once between four grinding wheels, hone if wanted, then pass the strip between strop wheels faced with stropping material.

เครื่องมือที่ต้องใช้:

ล้อเจียรล้อเจียร
สายหนังลับมีดสายหนังลับมีด
7

Wrap, break apart and pack

Wrap the strip spirally in paraffined paper. Then snap it at each weakened line over notched wheels, alternately from each side, and count and pack the blades.

เครื่องมือที่ต้องใช้:

กระดาษไขกระดาษไข

วัสดุ

1

เครื่องมือที่จำเป็น

6

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...