ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
13
0
0
0
0

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim

James Sangster of Buffalo, New York, received US 27,570, dated 20 March 1860, for a churn. A false bottom divides the churn; paddles spinning beneath it draw the cream and air down through holes near its centre and throw it up through holes near its rim, under caps that aim the streams against each other. Another paddle turns above. The cream goes round and round, from rim to centre and back. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days, plus printing

คำแนะนำ

1

Down at the centre, up at the rim

กำลังโหลดสมุด Jupyter…
2

An upright churn with a pierced cover, one week before

Wiswell's cover is above the scoops. Sangster's pierced partition is below the cream, with paddles under it.
3

Read US 27,570

"U and V represent caps which partially cover the apertures L and N. They are placed in such a position as to cause the fluid to flow in streams against each other, by boring the holes L and N at the same angles at which the caps U and V are set. The caps may be dispensed with and the same result obtained."
4

Print the caps Q, U, W, V

Hood cap 50 mm across, open on one side. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the crown wheel

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the pinion

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Rim Y and partition E

Screw a ring of HDPE strip 10 mm thick and 12 high inside the bucket with its top 60 mm above the floor, as the rim Y, sealing the screw holes outside with silicone. Cut a disc of 10 mm HDPE sheet to rest on it, bored 17 mm in the centre. Bore four 30 mm holes, H, I, J, K, 45 mm from the centre, a quarter turn apart, and four 25 mm holes, L, M, N, O, 112 mm from the centre between them, each bored at 45 degrees slanting toward the centre as it rises. Screw a printed cap over each rim hole, its open side toward the centre.

วัสดุสำหรับขั้นตอนนี้:

ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล16 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดโฮลซอว์ชุดโฮลซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ชุดไขควงชุดไขควง
8

Spindle D, paddles C, G and Z, shoulder J'

Screw a hardwood block 50 x 50 x 6 mm to the floor's centre and bore it 17 mm, 5 deep, as the step. Cut a 16 mm stainless spindle 435 mm long and turn or file its top 75 mm down to 12 mm. Fix a hardwood paddle bar 250 x 45 x 20 mm across it, 8 mm above the floor when the spindle stands in its step (the paddles C and G), pass it up through the partition, and fit a printed or hardwood collar 32 mm across and 20 high on it just above the partition as the shoulder J'. Fix a second paddle Z, 200 x 30 x 20 mm, across it 185 mm above the floor.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้2 ชิ้น
Shaft CollarShaft Collar2 ชิ้น
สลักผ่าสลักผ่า2 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
กระดาษทรายกระดาษทราย
ชุดไขควงชุดไขควง
9

Top I' and crank X

Cut a hardwood top 350 x 205 x 25 mm to sit on the bucket's rim and bore it 13 mm over the centre for the spindle; fit the pinion on the spindle above it. Screw two hardwood chairs on the top carrying a 12 mm stainless crank shaft with the crown wheel meshing the pinion, and fit a hardwood crank X with a dowel handle on its end.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้8 ชิ้น
Shaft CollarShaft Collar2 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
10

The build in 3D

FreeCAD model of this build, the bucket cut through the middle: the paddles C and G under the partition E on its rim Y, the centre and rim holes with their caps, the shoulder J', the paddle Z, and the top with the crank, crown wheel and pinion.
ไฟล์แบบBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket over the partition, set the top and gearing on the rim, and turn the crank steadily, timing it. When the butter comes, lift off the top, lift out the spindle and partition, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
12

Troubleshooting

False-bottom churn troubleshooting.

Flow

Loading...
13

History and honest limits

**James Sangster** of Buffalo, New York, US 27,570, 20 March 1860, "Churn". He claimed the paddles Z, C and G with the partition E pierced near its centre and near its rim under caps, "for the purpose of passing the cream around and around through the openings from circumference to center and vice versa". He made it of "wood, tin or any other suitable material"; ours is a food-grade bucket with an HDPE partition and printed caps and gears. Every size here is ours.

วัสดุ

16

เครื่องมือที่จำเป็น

19

ไฟล์ออกแบบ

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...