ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)
Charlie

สร้างโดย

Charlie

9. พฤศจิกายน 2026DE
16
0
0
0
0

Separating Funnel: Glass Stopcock with a Screw-On Plastic Stem (Demers, US 5,580,528)

A separating funnel holds two liquids that do not mix, so the lower layer can be run off through a tap at the bottom. J. P. Demers (US 5,580,528, 1996) fuses a bought glass stopcock to the bottom of a pear-shaped glass vessel and screws a flexible plastic stem onto it, because the usual glass stem breaks just below the stopcock. The glass stopcock body stays clear, so you can watch the boundary between the two liquids as it reaches the tap. Source: J. P. Demers, US Patent 5,580,528 (filed 1995, granted 1996). Picture: its Figs. 1-3.
ขั้นสูง
Unknown

คำแนะนำ

1

Read Demers

"The stresses resulting from such impacts usually fracture the glass just below the stopcock, or else chip off the end of the stem ... When the fracture is close to the stopcock, repair is impossible without replacing the stopcock".
2

Blow the vessel

Blow a glass vessel, pear-shaped (or spherical or cylindrical), with a neck at the top for pouring in the liquids and an opening at the bottom. Glass, size and how it is blown are not given; the patent leaves this to a scientific glassblower.

วัสดุสำหรับขั้นตอนนี้:

แก้วที่ไม่ทราบชนิดแก้วที่ไม่ทราบชนิด1 vessel

เครื่องมือที่ต้องใช้:

หัวเป่าแก้วตั้งโต๊ะหัวเป่าแก้วตั้งโต๊ะ
วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Fuse on the stopcock

Take a glass-bodied stopcock (bought: the patent calls them articles of commerce, with a glass or PTFE plug) and fuse its upper stem to the bottom of the vessel so the vessel opens straight into the stem. Form a male thread on the end of its lower stem (how is not given).

วัสดุสำหรับขั้นตอนนี้:

ก๊อกแก้วก๊อกแก้ว1 plug of glass or PTFE

เครื่องมือที่ต้องใช้:

หัวเป่าแก้วตั้งโต๊ะหัวเป่าแก้วตั้งโต๊ะ
วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
4

Make the plastic stem

Make a stem of moderately flexible plastic tube with a female thread in its upper end and an inner shoulder where the end of the glass thread meets it. Lay an O-ring on the shoulder when the funnel will hold reactive or toxic liquids or work under pressure or vacuum. Cut the lower end at about 45 degrees as a drip tip. The plastic is not given.

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 flexible plastic stem
โอริงโอริง1 ชิ้น

เครื่องมือที่ต้องใช้:

วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
5

Assemble and use

Screw the plastic stem onto the glass thread. Close the stopcock, pour the two liquids in at the neck, shake and let them separate, then turn the plug to line its bore up with the stems and run the lower layer off, watching the boundary through the glass stopcock. Unscrew the stem to clear a blocked stopcock.

วัสดุ

4

เครื่องมือที่จำเป็น

3

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...