ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Inclined-Wheel Cam Dog Power: A Dog Turns a Tilted Platform; a Zig-Zag Cam Rocks the Churn Lever
Dexter C. Slater of Laurens, New York, received US 24,338, dated 7 June 1859, for a simple, portable dog power for light machinery such as churns. A tilted platform is fixed square to an inclined shaft; a dog walking on it turns it. On the shaft's upper part a cam has a zig-zag groove right round it; a roller on the end of a lever runs in the groove, so the lever rocks on its pin as the shaft turns, and the work is taken from the lever.
This rung builds it full size for a dog, working a bucket churn's dasher.
ขั้นสูง
About 3 days, plus printing
คำแนะนำ
1
1
Slope, strokes and stroke length
Slope, strokes and stroke length
กำลังโหลดสมุด Jupyter…
2
2
A dog's tread-wheel working a churn, before it
A dog's tread-wheel working a churn, before it
Brush rocked a shaft with tappets on the wheel's rim. Slater rocks a lever with a grooved cam on the wheel's own shaft.
3
3
Read US 24,338
Read US 24,338
"The dog is placed on the wheel G, and rotates it by the movement of his legs, and the cam H, as it rotates gives a vibrating motion to the lever I, from which the power is taken."
4
4
Print the cam segment
Print the cam segment
A quarter of cam H with its share of the zig-zag groove. Print four. PETG, 0.2 mm layers, 50 % infill, 5 walls.
5
5
Print the step block
Print the step block
The 15-degree block on the sill for the shaft's lower bearing. PETG, 0.2 mm layers, 50 % infill, 5 walls.
6
6
Sills, posts and bar D
Sills, posts and bar D
From 70 mm square timber lay sill A 1665 mm long and a front sill 1000 mm long across its end. Stand post B upright and post C beside it, 260 mm apart, on the front sill, and join their tops with bar D running back 660 mm over the shaft's top. Screw the printed step block on sill A 870 mm behind the front sill and bolt a flange bearing on it; bolt a second flange bearing under bar D so a line between the two leans 15 degrees toward the posts.
วัสดุสำหรับขั้นตอนนี้:
ไม้เนื้ออ่อน 70x70 มม.6 ชิ้น
สกรูไม้ #10 x 3"30 ชิ้น
เส้นใย PETG1 ชิ้น
ตลับลูกปืนหน้าแปลน2 ชิ้น
ชุดสลักเกลียวหกเหลี่ยม M104 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน
ระดับน้ำ
ไม้โปรแทรกเตอร์
ตลับเมตร7
7
Shaft F and wheel G
Shaft F and wheel G
Halve two 70 mm timbers 1300 mm long into a cross for arms b, bore the crossing 30 mm and glue and screw two layers of 18 mm plywood cut to a 1400 mm disc on them as platform b'. Screw pine cleats on top for the dog's grip. Pass a 30 mm steel shaft 1335 mm long through the lower bearing, the wheel and the top bearing, and cross-bolt the wheel to it 250 mm above the step. The platform is square to the shaft, so it tilts 15 degrees.
วัสดุสำหรับขั้นตอนนี้:
ไม้เนื้ออ่อน 70x70 มม.2 ชิ้น
แผ่นไม้อัด5 ชิ้น
กาวไม้1 ชิ้น
ตะปูเกลียวไม้ #8 x 1 นิ้ว120 ชิ้น
แผ่นไม้สน1 ชิ้น
เพลาเหล็ก 30 มม.1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยม M101 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
แคลมป์
ประแจเลื่อน
กระดาษทราย8
8
Cam H, pendant E and lever I
Cam H, pendant E and lever I
Bolt the four cam segments round a hardwood hub on the shaft, 990 to 1150 mm above the step, so the groove runs unbroken round them. Screw two hardwood cheeks down from bar D as pendant E, about 190 mm in front of the cam's face, and drill them 12.5 mm for the fulcrum pin e. Cut a hardwood lever I 30 x 20 mm, 815 mm long, drilled for the pin 174 mm from its inner end. Fit a 28 mm printed or hardwood roller f on a 10 mm stainless stub through the inner end, set it in the groove and bolt the lever between the cheeks.
วัสดุสำหรับขั้นตอนนี้:
เส้นใย PETG1 ชิ้น
แผ่นไม้เนื้อแข็ง2 ชิ้น
สลักเกลียวหัวกลม8 ชิ้น
แหวนรองแบน12 ชิ้น
นอตล็อกไนลอน10 ชิ้น
แท่งสเตนเลส1 ชิ้น
สกรูไม้ #10 x 3"6 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ประแจเลื่อน9
9
The churn
The churn
Stand a food-grade 20-litre bucket under the lever's outer end, 600 mm beyond the pin. Hang a 12 mm stainless rod 900 mm long from the lever's end on a bolt, through a slot in the bucket's lid, with a 220 mm dasher of plywood screwed to its foot so it works between about 95 and 340 mm above the floor. Put an eye bolt in post B for the dog's lead.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แท่งสเตนเลส1 ชิ้น
แผ่นไม้อัด1 ชิ้น
ตะปูเกลียวไม้ #8 x 1 นิ้ว4 ชิ้น
ชุดสลักเกลียวหกเหลี่ยม M101 ชิ้น
สลักเกลียวหัวห่วง1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน10
10
The build in 3D
The build in 3D
FreeCAD model of this build: the sills, posts B and C and bar D, the tilted shaft in its bearings, the platform on its arms with cleats, the zig-zag cam, the pendant with lever I and its roller in the groove, and the rod and dasher into the bucket. It was checked at eight cam angles.
11
11
Train the dog and churn
Train the dog and churn
Use a harness, never a collar, on a lead to the eye bolt in post B, the dog standing on the platform facing up the slope. Start with short sessions and treats until it walks calmly. Pour about 9 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, put the lid on and let the dog walk; time it. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
สายรัดอกสุนัข1 ชิ้น
ชามใส่น้ำ1 ชิ้น
ครีมสด9 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่12
12
Troubleshooting
Troubleshooting
Dog-power troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Dexter C. Slater** of Laurens, Otsego County, New York, US 24,338, 7 June 1859. He meant it to be simple, cheap and portable, almost wholly of wood, with metal strips only to face the groove, and claimed the wheel, shaft, cam and lever together. He gave no sizes: the tilt, the platform, the cam's two zig-zags and throw, the lever and the bucket churn are ours.
วัสดุ
22- 6 ชิ้นตัวยึดตำแหน่ง
- 36 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 5 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 124 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 12 ชิ้นตัวยึดตำแหน่ง
- 10 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 9 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



