ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)
Charlie

สร้างโดย

Charlie

31. ตุลาคม 2026DE
13
0
0
0
0

Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)

A short-stroke solenoid that opens an air valve. One coil pulls the iron armature down; a second, weaker coil holds it there against the air pressure once the first is switched off. A cast-iron shell closes the magnetic circuit around both. Result: an iron-clad plunger solenoid driving a brass valve rod through its hollow core. Source: C. P. Nachod's test (Electrical World, 1905) in Underhill, Solenoids, Electromagnets and Electromagnetic Windings (1910), pp. 125-129. Unknown: the wire insulation; the test does not give it. Not given: shell and armature sizes, voltage. Picture drawn by Youblob.
ขั้นสูง
2 days

คำแนะนำ

1

Turn the core and armature

Turn the core from Norway iron to 3.17 cm outside diameter and bore a 0.95 cm hole through it for the valve rod. Turn the armature from the same iron. Ours: wrought iron bar; the armature size is not given.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 as required

เครื่องมือที่ต้องใช้:

ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
2

Cast the shell and top

Cast the shell and top in cast iron so they close the magnetic circuit round the coils, leaving a round clearance gap for the armature in the top. Sizes: not given (Underhill's Fig. 92 shows the layout).

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดิบแท่งเหล็กดิบ1 as required

เครื่องมือที่ต้องใช้:

เตาคิวโพลาเตาคิวโพลา
กระบะแบบหล่อทรายกระบะแบบหล่อทราย
ทรายหล่อทรายหล่อ
3

Wind coil A: 1860 turns of No. 25

Wind the operating coil, 1860 turns of No. 25 wire, and place it where it encircles the working air gap between armature and core. Copper, as Underhill gives for magnet windings. Unknown: the insulation; the test does not give it.

วัสดุสำหรับขั้นตอนนี้:

ลวดทองแดงลวดทองแดง1 as required
วัสดุฉนวนที่ไม่ทราบวัสดุฉนวนที่ไม่ทราบ1 as required

เครื่องมือที่ต้องใช้:

ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
4

Wind coil B: 1765 turns of No. 26

Wind the retaining coil, 1765 turns of No. 26 wire, and place it below coil A on the core. Being away from the gap, it pulls only 0.4-0.8 as hard as A, enough to hold the armature down.

วัสดุสำหรับขั้นตอนนี้:

ลวดทองแดงลวดทองแดง1 as required

เครื่องมือที่ต้องใช้:

ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
5

Assemble with the brass valve rod

Fit core, coils and armature in the shell and pass the brass rod through the core to the valve. Nachod set test gaps of 0.41 and 2.05 mm with brass washers.

วัสดุสำหรับขั้นตอนนี้:

แท่งทองเหลืองแท่งทองเหลือง1 as required

เครื่องมือที่ต้องใช้:

ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)

วัสดุ

5

เครื่องมือที่จำเป็น

4

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...