ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Spanner Set: Open-End Wrenches for 1/4 to 1 Inch Bolts (Machinery's Handbook, 1924)
Forge

สร้างโดย

Forge

3. พฤศจิกายน 2026NO
8
0
0
0
0

Spanner Set: Open-End Wrenches for 1/4 to 1 Inch Bolts (Machinery's Handbook, 1924)

A set of open-end spanners made to the standard dimensions in Machinery's Handbook. The jaw opening fits the nut of each bolt size, and head width, head thickness and length grow with it, so each spanner is strong enough for its own nut. Variable: the bolt size. The table gives each spanner's dimensions from 1/4 in up to 3 1/2 in bolts; this set covers 1/4 to 1 in. Source: Machinery's Handbook (1924), p. 848, Dimensions of Wrenches. Unknown: the steel and its hardening. Picture: the Handbook's page.
ระดับกลาง
Unknown

คำแนะนำ

1

Pick the sizes

For each bolt size, the Handbook gives jaw opening A, head width B, head thickness H and overall length L, in inches. 1/4 in bolt: 1/2, 1, 1/4, 5 1/2. 5/16: 19/32, 1 3/16, 5/16, 6. 3/8: 11/16, 1 3/8, 3/8, 7. 7/16: 25/32, 1 9/16, 7/16, 8. 1/2: 7/8, 1 3/4, 1/2, 9. 9/16: 31/32, 1 15/16, 9/16, 10. 5/8: 1 1/16, 2 1/8, 5/8, 11. 3/4: 1 1/4, 2 1/2, 11/16, 12 1/2. 7/8: 1 7/16, 2 15/16, 3/4, 14 1/2. 1 in: 1 5/8, 3 5/16, 7/8, 16 1/2. The neck and handle sizes are in the same table. Ours: a set of these ten.

เครื่องมือที่ต้องใช้:

ไมโครมิเตอร์ไมโครมิเตอร์
2

Forge the blanks

Forge each spanner from bar: a round head as wide as B and as thick as H, a neck, and a handle to make the overall length L. Ours: carbon steel bar forged under a power hammer. Not given: the steel, the forging method.

วัสดุสำหรับขั้นตอนนี้:

เหล็กกล้าคาร์บอนเส้น (0.6 % C)เหล็กกล้าคาร์บอนเส้น (0.6 % C)10 ten spanners

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
ค้อนกลค้อนกล
ทั่งทั่ง
3

Cut the jaws and harden

Cut the open jaw in each head to the opening A, so it fits across the flats of that bolt's nut, and finish the faces parallel. Check each opening. Harden and temper the spanners. Not given: the hardening.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
ตะไบโลหะตะไบโลหะ
ไมโครมิเตอร์ไมโครมิเตอร์
เตาอบชุบความร้อนเตาอบชุบความร้อน
ถังชุบน้ำถังชุบน้ำ

วัสดุ

1

เครื่องมือที่จำเป็น

8
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...