ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)
Volt

สร้างโดย

Volt

3. พฤศจิกายน 2026SE
15
0
0
2
0

Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)

A small steam boiler for model engines and boats: a brass cylinder 4 in across, closed by two brass heads tied together by a brass stay rod, its seam held by two rows of brass screws and sealed with solder. It sits in a russia-iron jacket over an alcohol lamp, with a weighted safety valve and fusible plugs that put the lamp out if the water runs low. Result: a strong little shell boiler, 6 to 12 in long to suit the engine. Source: N. M. Hopkins, Model Engines and Small Boats (1898), ch. III. Unknown: the working pressure and the valve's sizes. Picture: the book's Fig. 33.
ระดับกลาง
Unknown

คำแนะนำ

1

Make the heads and stay

Cut two brass disks 4 in across and about 1/8 in thick, each with a 1/4 in hole in the centre, and true them up in the lathe. Pass a 1/4 in brass rod through both and solder it, with plenty of solder inside the heads to make them steam-tight. Screw heavy brass disks (round nuts are better than square) onto the rod ends against the heads. Set the heads 10 in apart over their outsides; about 6 in will do for a small single-acting engine, 7 in for a double engine, up to 12 in for a larger one.

วัสดุสำหรับขั้นตอนนี้:

แท่งทองเหลืองกลมแท่งทองเหลืองกลม1 two heads, two nuts
แท่งทองเหลืองแท่งทองเหลือง1 1/4 in stay
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 as needed
ฟลักซ์ฟลักซ์1 as needed

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ตะเกียงบุนเซนตะเกียงบุนเซน
2

Roll and screw the shell

Cut soft sheet brass at least 1/32 in thick (1/16 in for boilers over 8 in long), about 14 in long and 1/2 in longer than the heads so it overhangs 1/4 in each end. Roll it round the heads on tinner's rollers, never by hand, so it laps about 1 in. Slip it over the heads and rod and bind it tight with heavy twine. Drill two rows of holes along the lap, tap them and turn in little brass screws that go just through the under plate without projecting. Do not use iron screws: their rust pits the seams.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 shell
สกรูเกลียวมิลสกรูเกลียวมิล1 small brass screws
เชือกมัดของเชือกมัดของ1 binding

เครื่องมือที่ต้องใช้:

เครื่องม้วนแผ่นเหล็กเครื่องม้วนแผ่นเหล็ก
สว่านมือสว่านมือ
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
3

Solder it up

Push the heads and rod out, hold the shell in a Bunsen flame and run solder well along the seam. Push the heads back and solder them all round the edge, and screw the nuts tight: the screws and stay take the strain, the solder keeps in the steam. Drill two or three 1/4 in holes in the top and bush them with heavy brass disks soldered on. For fusible plugs, drill two 1/4 in holes near the bottom and solder them shut with little brass caps.

วัสดุสำหรับขั้นตอนนี้:

ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 as needed
ฟลักซ์ฟลักซ์1 as needed
แท่งทองเหลืองกลมแท่งทองเหลืองกลม1 bushes and plug caps

เครื่องมือที่ต้องใช้:

ตะเกียงบุนเซนตะเกียงบุนเซน
สว่านมือสว่านมือ
4

Fit the jacket and safety valve

Cut end supports from russia sheet iron to hold the boiler by its ends, with an opening for the alcohol lamp, and bend a russia-iron cover over it, riveted to the ends by little ears. Punch a row of small holes along the cover's lower edge to let air in for the lamp; the cover keeps in the heat and keeps draughts off the flame. Turn a small safety valve true in the lathe, grind it to its seat with emery and oil, and fit a lead weight on its bar. Not given: the valve's sizes.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กรัสเซียแผ่นเหล็กรัสเซีย1 ends and cover
หมุดย้ำเหล็กหมุดย้ำเหล็ก1 small
แท่งทองเหลืองกลมแท่งทองเหลืองกลม1 valve
ตะกั่วตะกั่ว1 weight

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ชุดย้ำหมุดชุดย้ำหมุด
เครื่องกลึงโลหะเครื่องกลึงโลหะ
ผ้าทรายอีเมอรีผ้าทรายอีเมอรี
5

Fire and set it

Fill the boiler two-thirds full, connect the engine and light the alcohol lamp under it. If the valve blows off before the engine turns over, move the weight a little farther out until the engine runs without steam escaping; well made, the valve will then blow off soon after the engine stops if the fire is left. If the water ever runs very low, the fusible plugs melt and the steam puts out the lamp. Do not try to burst a boiler to test it.

เครื่องมือที่ต้องใช้:

ตะเกียงแอลกอฮอล์ตะเกียงแอลกอฮอล์

วัสดุ

10

เครื่องมือที่จำเป็น

9

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...