ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Frank A. Stanley · Public domain (1919)
Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)
Die makers made their own dowel pins two at a time: one piece of steel is turned, necked in the middle, hardened, ground dead straight to size from each end, then snapped in two at the neck. Frank Stanley described the practice of one die shop.
Source: F. A. Stanley, Punches and Dies (1919), pp. 417–419. The choice of tool steel and the forge for hardening are ours; the passage gives no hardening heat. Picture: Stanley's Fig. 610, grinding dowel pins.
ระดับกลาง
1 day
คำแนะนำ
1
1
Cut stock for two pins
Cut stock for two pins
Take a length of steel a little larger than the dowel size and long enough for two pins. It must harden, so use tool steel (our choice).
วัสดุสำหรับขั้นตอนนี้:
เหล็กเครื่องมือแปดเหลี่ยม1 length for two pinsเครื่องมือที่ต้องใช้:
ปากกาจับชิ้นงานหน้าโต๊ะ2
2
Turn 0.008 in over size
Turn 0.008 in over size
Turn it on centres to about 0.008 in above the finished size.
เครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ
ตัวพาหมุนงานกลึง
ไมโครมิเตอร์3
3
Neck it in the middle
Neck it in the middle
Cut a neck 1/16 in deep in the middle, the dividing line between the two pins.
เครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ4
4
Harden
Harden
Harden the piece. This passage gives no heat; heat to hardening heat and quench in the usual way for your steel (ours).
เครื่องมือที่ต้องใช้:
เตาตีเหล็กของช่างตีเหล็ก
คีมคีบ
ถังชุบน้ำ5
5
Grind each half to size
Grind each half to size
Put it on dead centres in the grinding machine and grind the diameter to size from one end to the neck. Reverse it on the centres and grind from the other end. The pins come out perfectly straight from end to end.
เครื่องมือที่ต้องใช้:
เครื่องเจียระไนทรงกระบอก
ตัวพาหมุนงานกลึง
ไมโครมิเตอร์6
6
Break the pins apart
Break the pins apart
Break the piece apart at the neck. You have two dowel pins ground closely to standard size; ream their holes true and straight to fit.
เครื่องมือที่ต้องใช้:
ปากกาจับชิ้นงานหน้าโต๊ะวัสดุ
1- 1 length for two pinsตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
