ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Stick Shuttle Cut from a Beech Strip
The shuttle carries the weft yarn through the shed of the loom. The simplest is the stick shuttle: a flat, narrow piece of hard wood with notches at the ends to hold the wound weft. Saw a thin beech strip a little longer than the cloth is wide, cut forked notches at both ends, round every edge and polish it smooth so it slides.
The picture: two stick shuttles wound with yarn.
เริ่มต้น
An afternoon
คำแนะนำ
1
1
Cut the strip
Cut the strip
Saw and plane a straight-grained beech strip about 6 mm thick and 4 cm wide, a little longer than the cloth is wide (step 5).
วัสดุสำหรับขั้นตอนนี้:
ไม้บีชแปรรูป1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
กบไสไม้
ไม้บรรทัด2
2
Cut the notches
Cut the notches
Drill a hole near each end and saw from the end into it, making a forked notch that holds the yarn. Cut a shallow long slot in the middle if you like, to make the shuttle lighter.
เครื่องมือที่ต้องใช้:
สว่านมือ
เลื่อยฉลุ3
3
Round and smooth
Round and smooth
Round all the edges and points with the knife and rasp so nothing can catch the warp, then sand it smooth.
เครื่องมือที่ต้องใช้:
มีดสโลยด์
ตะไบหยาบสำหรับไม้
กระดาษทราย4
4
Wax it
Wax it
Rub in beeswax and polish so the shuttle slides through the shed.
วัสดุสำหรับขั้นตอนนี้:
ขี้ผึ้ง0.01 กก.เครื่องมือที่ต้องใช้:
กระดาษทราย5
5
Shuttle length for the cloth
Shuttle length for the cloth
กำลังโหลดสมุด Jupyter…
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

