ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
9
0
0
0
0

Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)

A. Graves Williams III and Ronald L. Thackston of Ohio received US 4,682,917, dated 28 July 1987, for The Irwin Company. They kept Robinson's flutes on the point and added a flute along each shoulder's cutting edge, joining the point flute. Each flute stops just short of the outside, closed by a sharp spur at the corner whose inner edge slopes into it. The spur scores the rim of the hole. In oak their bits bored up to twice as fast as Robinson's, and left a clean exit instead of a splintered one. We forge three of their test sizes, 5/8, 7/8 and 1 inch. The patent gives the angles; the other sizes are ours.
ขั้นสูง
About 1 day

คำแนะนำ

1

Their tests

กำลังโหลดสมุด Jupyter…
2

Read US 4,682,917

"If the flutes are 'stopped', that is, if they do not extend or 'open' to the respective outer sides of the blade, and if cutting spurs are provided at the outer corners of the shoulders so that the spurs 'close' the flutes, then this splitting is virtually eliminated and cutting proceeds more smoothly."
3

Forge the blades

Cut three 170 mm lengths of 10 mm octagonal tool steel. Heat 50 mm of one end to a bright orange in the forge and flatten it on the anvil to about 3 mm thick, centred on the bar. Hammer across it with the peen to spread it wider than the bit, about 2 mm over its size: 18, 24 and 27 mm. Draw the neck down smoothly where the blade meets the bar and keep the blade in line with it. Reheat as soon as the colour fades to red. Finally heat each one to a cherry red and let it cool slowly in the air, to soften it for filing.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือแปดเหลี่ยมเหล็กเครื่องมือแปดเหลี่ยม3 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เตาตีเหล็กเตาตีเหล็ก
ทั่งทั่ง
ค้อนตีเหล็กค้อนตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ถุงมืองานเชื่อมถุงมืองานเชื่อม
แว่นนิรภัยแว่นนิรภัย
4

Print the grinding template

Full-size A4 template: the outlines of the 5/8, 7/8 and 1 inch bits with square shoulders and corner spurs, the joined point and shoulder flutes on one face, and the hanging hole. Print at 100 %; its 50 mm bar must measure 50 mm.
ไฟล์แบบPDFCC0 - Free
5

Grind the outline

Glue each bit's outline from the template on its blade, centred on the bar. Grind to the lines on the bench grinder, dipping the steel in water often: the two sides parallel, the shoulders square across, the point in the middle. Grind the blade's two faces flat and parallel to 2.5 mm. Grind three flats on the end of the shank, a third of the way round from each other, 20 mm long, for the chuck's jaws. Leave a spur 2 mm wide and 2 mm high at each outer corner of the shoulders. Drill a 3 mm hole at the template's circle.

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์อิงก์เจ็ตเครื่องพิมพ์อิงก์เจ็ต
กาวกาว
เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
ชุดตะไบชุดตะไบ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
6

Bevel the edges and file the flutes

Bevel the outer sides and the shoulders' cutting edges slightly, so each edge meets its leading face at about 86 degrees. On the face towards you, file the point flute along the point's left edge with the 3 mm round needle file, 0.3 mm deep. Then file the shoulder flute with the three-square needle file along the left shoulder, right behind its cutting edge and square to the bit's axis, from the point flute to the spur, and stop there. Bevel the spur's inner edge into the flute so the spur has a sharp outer edge. Turn the bit over and do the same along that face's left edge and shoulder.

เครื่องมือที่ต้องใช้:

เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ชุดตะไบเข็มชุดตะไบเข็ม
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
7

Harden and temper

Heat the blade and the neck evenly to a cherry red, until a magnet no longer sticks to it, and quench it straight down in water, moving it up and down. Rub the faces bright with a stone. Heat the shank gently 30 mm behind the blade and watch the colours run down; quench again as soon as a dark straw colour reaches the shoulders and the point. Do the other two.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
แม่เหล็กเล็กแม่เหล็กเล็ก
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
หินลับมีดหินลับมีด
ถุงมืองานเชื่อมถุงมืองานเชื่อม
แว่นนิรภัยแว่นนิรภัย
8

Sharpen and test

Hone the cutting edges on the shoulders and the point with the stone, keeping their angles, and take the burr off. Chuck a bit by its flats and bore a scrap of hardwood: it should start on the point without wandering, cut two clean shavings from the shoulders and leave a round hole of its own size; check it with the caliper.

เครื่องมือที่ต้องใช้:

หินลับมีดหินลับมีด
สว่านไร้สายสว่านไร้สาย
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
9

Troubleshooting

Spade bit troubleshooting.

Flow

Loading...
10

History and honest limits

**A. Graves Williams III**, Wilmington, and **Ronald L. Thackston**, Hillsboro, Ohio, assignors to The Irwin Company, US 4,682,917, dated 28 July 1987, filed 24 January 1986. They claimed "cutting spurs projecting forwardly from the shoulders" with sharp outer edges, and shoulder flutes from the point flutes towards the spurs, "terminating at the spurs so that the shoulder flutes do not extend across the spurs to the outer sides of the blades". They prefer the flutes forged and the flute wall at about 68 degrees; we file them, with a three-square file at 60 degrees, inside their "less than about 78". Their shank has a hexagonal end; ours is octagonal tool steel with three ground flats. They give no heat treatment or spur size; those are ours.

วัสดุ

1

เครื่องมือที่จำเป็น

20

ไฟล์ออกแบบ

1

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...