කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Hand Lens 10×: a Small, Steep Lens Ground and Mounted
Penny

නිර්මාතෘ

Penny

14. ඔක්තෝබර් 2026DK
9
0
0
0
0

Hand Lens 10×: a Small, Steep Lens Ground and Mounted

A 10× hand lens is a small convex lens of about 25 mm focal length: held close to the eye, its magnifying power is about a quarter of a metre divided by the focal length. Grind a small pair of discs to a steep curve as for any convex lens, then seat the convex one in a turned wooden ring with a cord to carry it. The picture: a low-power reading magnifier on a dictionary page; a 10× hand lens works the same way with a much smaller, steeper lens.
උසස්
A week

උපදෙස්

1

Two small discs

Cut two small glass discs, about 15 mm across, from glass at least 5 mm thick (each face of the lens goes over a millimetre deep), and pitch each to a short wooden handle.

මෙම පියවර සඳහා ද්‍රව්‍ය:

වීදුරු තහඩුවවීදුරු තහඩුව1 කැබැල්ල
පයින් තාර ඇලවුමපයින් තාර ඇලවුම10 ග්‍රෑ
දැඩි දැව තීරුවදැඩි දැව තීරුව1 කැබැල්ල

අවශ්‍ය මෙවලම්:

වීදුරු කපනයවීදුරු කපනය
වීදුරු කපන අඬුවවීදුරු කපන අඬුව
ආරක්ෂිත කණ්ණාඩිආරක්ෂිත කණ්ණාඩි
2

Grind to a steep curve

Grind them together with wet coarse grit, the same disc always on top, until the faces are steep enough (see the notebook). Then the second faces. The bottom disc is the lens.

මෙම පියවර සඳහා ද්‍රව්‍ය:

සිලිකන් කාබයිඩ් දැල්ලසිලිකන් කාබයිඩ් දැල්ල40 ග්‍රෑ
ජලයජලය1 ලීටර්

අවශ්‍ය මෙවලම්:

ඩිජිටල් කැලිපරය අඟල් 6ඩිජිටල් කැලිපරය අඟල් 6
3

Fine grind and polish

Fine grits, then polish both faces on a small pitch lap with tin oxide and water until clear.

මෙම පියවර සඳහා ද්‍රව්‍ය:

සිලිකන් කාබයිඩ් දැල්ලසිලිකන් කාබයිඩ් දැල්ල20 ග්‍රෑ
ටින් ඔක්සයිඩ් (ස්ටැනික් ඔක්සයිඩ්)ටින් ඔක්සයිඩ් (ස්ටැනික් ඔක්සයිඩ්)10 ග්‍රෑ
පයින් තාර ඇලවුමපයින් තාර ඇලවුම30 ග්‍රෑ
4

Check 10×

Focus the sun through it onto paper: the spot should be smallest about 25 mm from the lens. Grind deeper if it is longer.

අවශ්‍ය මෙවලම්:

රූලක්රූලක්
5

Turn the mount

Turn a hardwood ring on the lathe with a seat a snug fit for the lens and a small lip. Press the lens in, warm a little pitch round the back edge to hold it, drill a hole in the rim for a cord loop.

මෙම පියවර සඳහා ද්‍රව්‍ය:

දැඩි දැව තීරුවදැඩි දැව තීරුව1 කැබැල්ල
පයින් තාර ඇලවුමපයින් තාර ඇලවුම2 ග්‍රෑ
ඉටි ගෑ ලිනන් නූලඉටි ගෑ ලිනන් නූල0.5 m

අවශ්‍ය මෙවලම්:

ලී කරකැවීමේ යන්ත්‍රයලී කරකැවීමේ යන්ත්‍රය
වක්‍ර නියනවක්‍ර නියන
කපා වෙන් කරන උල්ල (ලේත් යන්ත්‍රය)කපා වෙන් කරන උල්ල (ලේත් යන්ත්‍රය)
වැලි කඩදාසිවැලි කඩදාසි
ඩිජිටල් කැලිපරය අඟල් 6ඩිජිටල් කැලිපරය අඟල් 6
6

Curve for 10×

Jupyter සටහන් පොත පූරණය වෙමින්…
7

Use

Hold the lens close to your eye and bring the object up until it is sharp.

ද්‍රව්‍ය

7

අවශ්‍ය මෙවලම්

9

සම්බන්ධ බ්ලූප්‍රින්ට්

මෙම බ්ලූප්‍රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්‍රම, ද්‍රව්‍ය හෝ මූලධර්ම

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...