කලාව
රූපලාවණ්‍ය සහ සුවතාව
ශිල්පය
සංස්කෘතිය සහ ඉතිහාසය
විනෝදාස්වාදය
පරිසරය
ආහාර සහ පාන
ප්‍රතිලෝම ඉංජිනේරු
විද්‍යාවන්
ක්‍රීඩා
තාක්ෂණය
පැළඳිය හැකි
Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads
Woody

නිර්මාතෘ

Woody

14. ඔක්තෝබර් 2026NO
6
0
0
0
0

Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads

A barrel is the cooper's closed vessel: oak staves held by hoops, bulging at the middle, with flat heads set in grooves at both ends. Coopers heat the staves to bend them. Shape staves wider at the middle than the ends, raise them in a hoop, heat them over a small fire and draw the open end together, drive the hoops, and fit the heads. The picture: a new oak barrel in a cooper's workshop, with iron hoops on the floor.
උසස්
Several days

උපදෙස්

1

Shape the staves

Rive and shave oak staves as for the vat, but taper each from the middle toward both ends, and hollow the inside face a little.

මෙම පියවර සඳහා ද්‍රව්‍ය:

දැඩි දැව ඝන පලංචියදැඩි දැව ඝන පලංචිය8 කැබලි

අවශ්‍ය මෙවලම්:

ෆ්‍රෝ (පලන පිහිය)ෆ්‍රෝ (පලන පිහිය)
සූරන බංකුවසූරන බංකුව
අත් දෙකේ ඇදුම් පිහියඅත් දෙකේ ඇදුම් පිහිය
අත් ලීයන යන්ත්‍රයඅත් ලීයන යන්ත්‍රය
2

Raise and fire

Stand the staves inside one hoop to form a skirt. Light a small charcoal fire inside, wet the outside, and as the staves warm, draw the open end together with a rope round it until a hoop can be driven on.

මෙම පියවර සඳහා ද්‍රව්‍ය:

අඟුරුඅඟුරු3 as required
ජලයජලය10 ලීටර්

අවශ්‍ය මෙවලම්:

යකඩ වළල්ලයකඩ වළල්ල
ශක්තිමත් ලණුවශක්තිමත් ලණුව
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
තාපයට ඔරොත්තු දෙන අත්වැසුම්තාපයට ඔරොත්තු දෙන අත්වැසුම්
3

Hoops

Drive the rest of the iron hoops on, two near each end and two at the quarters, until the joints close tight.

මෙම පියවර සඳහා ද්‍රව්‍ය:

යකඩ වළල්ලයකඩ වළල්ල6 කැබලි

අවශ්‍ය මෙවලම්:

හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
4

Ends and grooves

Level the ends and bevel the inside edge with the adze, then cut a groove round the inside near each end.

අවශ්‍ය මෙවලම්:

වක් පොරොවවක් පොරොව
නියන් කට්ටලයනියන් කට්ටලය
5

Heads and bung

Join planks into two boards, scribe circles to fit the grooves, cut and bevel them, slack the end hoops and spring the heads in. Bore a bung hole in the middle stave. Fill with water to swell it tight.

මෙම පියවර සඳහා ද්‍රව්‍ය:

දැඩි දැව ඝන පලංචියදැඩි දැව ඝන පලංචිය2 කැබලි
ජලයජලය50 ලීටර්

අවශ්‍ය මෙවලම්:

තුඩු දෙකේ මිනුම් කවකටුවතුඩු දෙකේ මිනුම් කවකටුව
අත් කියතඅත් කියත
අත් ලීයන යන්ත්‍රයඅත් ලීයන යන්ත්‍රය
හරස් කුඤ්ඤ හිසක් සහිත මිටියහරස් කුඤ්ඤ හිසක් සහිත මිටිය
අත් විදුමඅත් විදුම
6

Capacity of a barrel

Jupyter සටහන් පොත පූරණය වෙමින්…

ද්‍රව්‍ය

4
  • ස්ථානගත
  • 3 as required
    ස්ථානගත
  • 60 ලීටර්
    ස්ථානගත
  • 6 කැබලි
    ස්ථානගත

අවශ්‍ය මෙවලම්

13

මෙම සැලසුම සාදන්නේ

සම්බන්ධ බ්ලූප්‍රින්ට්

මෙම බ්ලූප්‍රින්ට් දැනුම බෙදා ගනී — ශිල්ප ක්‍රම, ද්‍රව්‍ය හෝ මූලධර්ම

CC0 පොදු වසම

මෙම බ්ලූප්‍රින්ට් CC0 යටතේ නිකුත් කර ඇත. ඔබට අවසර නොමැතිව පිටපත් කිරීම, වෙනස් කිරීම, බෙදා හැරීම සහ භාවිතා කිරීම කළ හැක.

බ්ලූප්‍රින්ට් හරහා නිෂ්පාදන මිලදී ගැනීමෙන් නිර්මාතෘට සහාය වන්න නිර්මාතෘ කොමිසම විකුණුම්කරුවන් විසින් නියම කළ, හෝ මෙම බ්ලූප්‍රින්ට්හි නව අනුවාදයක් සාදා ආදායම බෙදා ගැනීමට ඔබේ බ්ලූප්‍රින්ට්හි සම්බන්ධතාවයක් ලෙස ඇතුළත් කරන්න.

සාකච්ඡාව

(0)

පිවිසෙන්න සාකච්ඡාවට එක්වීමට

අදහස් පූරණය කරමින්...