Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Bellows-and-Float Atmospheric Churn: Blasts of Air Through a Water-Jointed Pipe, a Float Gathers the Butter
Buttercup

Зохиогч

Buttercup

9. Арван нэгдүгээр сар 2026IE
3
0
0
0
0

Bellows-and-Float Atmospheric Churn: Blasts of Air Through a Water-Jointed Pipe, a Float Gathers the Butter

Patrick S. Devlan of Reading, Pennsylvania, received US 24,382, dated 14 June 1859, for a churn worked by blasts of air only. A bellows under the body, worked by a lever, blows up a pipe that opens inside a wider tube; the air goes down between them and out through a perforated disk across the bottom, so it is spread through the whole cream. The cream standing in the tube makes a water joint, so no valves are needed. A perforated float with projections rides up and down on the bubbling cream and gathers the butter as it forms. This rung builds it with a 20-litre bucket on legs and a bellows below.
Дунд шат
About 1 day, plus printing

Зааварчилгаа

1

The water joint

Jupyter дэвтэр ачаалж байна…
2

Air drawn into the cream, before it

Wicks drew air in with turning funnels and a dasher. Devlan blows it in with a bellows and has no dasher at all.
3

Read US 24,382

"... this pipe or tube, C, is open at its upper end, but is entirely surrounded to within a short distance of its base by another tube D, of greater diameter which tube D, is connected at its base to the center of the convex perforated disk d."
4

Print the teat e

The hollow teat for the lid's middle, over tube D's top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
5

Print the collar

The collar that seals tube D into the disk's middle. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
6

Stand and bellows

Cut three legs a from 44 mm square timber 650 mm long and set them 120 degrees apart round a 350 mm circle. Screw a plywood seat ring 400 mm across, with a 60 mm hole, between them 482 mm up to carry the bucket, a band 600 mm up round the bucket, and a plywood shelf 150 mm up for the bellows. Screw a bellows about 260 x 120 mm to the shelf.

Энэ алхмын материал:

Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм2 ширхэг
Фанер хуудасФанер хуудас2 ширхэг
Модны шурагМодны шураг24 ширхэг
Модны цавууМодны цавуу1 ширхэг
ХөөрөгХөөрөг1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Хөрөө (лобзик)Хөрөө (лобзик)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
7

Pipe C, tube D and disk d

Drill the middle of the bucket's floor 16.5 mm and seal a 16 mm stainless pipe C through it with silicone so it stands 400 mm up. Drill 24 holes of 4 mm in two rings in a stainless bowl about 260 mm across and a 32.5 mm hole in its middle, and stand it upside down on the floor round the pipe as disk d. Push a 32 mm stainless tube D 360 mm long through the printed collar into the bowl's middle hole, sealed with silicone, so it surrounds pipe C down to 56 mm above the floor. Run silicone tubing from the bellows' nozzle to pipe C's foot under the floor.

Энэ алхмын материал:

20 литрийн хувин20 литрийн хувин1 ширхэг
Зэвэрдэггүй ган хоолойЗэвэрдэггүй ган хоолой2 ширхэг
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга1 ширхэг
Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг
PETG филаментPETG филамент1 ширхэг
Силиконон хоолойСиликонон хоолой1 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Нүх хөрөөдөгч багцНүх хөрөөдөгч багц
Хоолой огтлогчХоолой огтлогч
Дүрд (гар дүрд)Дүрд (гар дүрд)
8

Lid, float and lever

Cut a 45 mm hole in the middle of the bucket's lid and glue the teat e over it, with its cap f. Cut float G from 15 mm plywood, 250 mm across with a 48 mm hole for tube D and eight 22 mm holes, and glue 10 mm dowel pegs 25 mm long into both faces as the projections g. Bolt a hardwood lever b to the outside of one leg 360 mm up, running up beside the bucket to a handle c above the lid, and join it to the bellows' top board with a hardwood link.

Энэ алхмын материал:

PETG филаментPETG филамент1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Фанер хуудасФанер хуудас1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Хатуу модон банзХатуу модон банз2 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга3 ширхэг
Хавтгай угаагуурХавтгай угаагуур6 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка3 ширхэг

Шаардлагатай багаж:

Нүх хөрөөдөгч багцНүх хөрөөдөгч багц
Хөрөө (лобзик)Хөрөө (лобзик)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Гар хөрөөГар хөрөө
Элсэн цаасЭлсэн цаас
Тохируулгатай түлхүүрТохируулгатай түлхүүр
9

The build in 3D

FreeCAD model of this build, the near half of the body cut away: the stand with its seat, band and shelf, the bellows and hose, pipe C inside tube D, the drilled bowl as disk d, the float with its pegs, the lid with its teat and cover, and the lever with its link.
Дизайны файлBLENDCC0 - Free
10

Churn

Fill the bucket about one third full: about 6.5 litres of heavy cream at about 15 °C, checked with the thermometer. Drop the float in over tube D and put the lid on. Work the lever steadily and time it: each stroke blows a burst of air up the pipe, down the tube and out through the bowl's holes. When the butter has gathered on the float, lift it out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий6.5 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
11

Troubleshooting

Atmospheric churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Patrick S. Devlan** of Reading, Berks County, Pennsylvania (the drawing spells it Devlen), US 24,382, 14 June 1859. Earlier blast churns, he wrote, blew the air in one place, needed valves and did not collect the butter; he claimed the float in a churn worked by blast only. His only quantity is "say one third full". His pipe C rises straight from the bellows and his disk d spans the floor; our hose, drilled bowl, pegs and every size are ours.

Материал

19

Шаардлагатай багаж

15

Загварын файлууд

3

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...