Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
Дээд шат
A day at the forge per pair
Зааварчилгаа
1
1
Read Edwinson
Read Edwinson
"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2
2
Weld the blanks
Weld the blanks
As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.
Энэ алхмын материал:
Давтсан төмөр гулдмай1 ширхэг
Тигелийн ган1 ширхэг
Борын нунтаг1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Том алх
Халуун цүүц
Дархны хавчаар3
3
Bottom swage
Bottom swage
Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).
Шаардлагатай багаж:
Дархны зуух
Дөш
Алх
Дархны хавчаар4
4
Top swage
Top swage
Forge the matching top tool with a neck for its handle.
Шаардлагатай багаж:
Дархны зуух
Дөш
Алх
Дархны хавчаар5
5
Cut the grooves
Cut the grooves
Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.
Шаардлагатай багаж:
Дархны зуух
Фуллер (ховил гаргах төмөр)
Дөш
Дүрд (гар дүрд)6
6
Handle or spring
Handle or spring
Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).
Энэ алхмын материал:
Самрын мөчир (ногоон, уян)1 ширхэг
Зөөлөн ган дугуй саваа1 ширхэг
Төмөр утас1 ширхэг
Пүршний ган тууз1 ширхэгШаардлагатай багаж:
Дархны зуух
Дөш
Алх7
7
Grind and harden
Grind and harden
Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).
Шаардлагатай багаж:
Эргэдэг хурцлах чулуу
Дархны зуух
Хатууруулах тэвш8
8
Use them
Use them
Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.
Шаардлагатай багаж:
Дархны зуух
Том алх
Штангенциркуль9
9
Troubleshooting
Troubleshooting
Swage troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.
Материал
7- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Шаардлагатай багаж
11- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.




