Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)
Forge

Зохиогч

Forge

14. Арван нэгдүгээр сар 2026NO
9
0
0
0
0

A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)

Robert Gibson Griswold's working set of cold chisels from Amateur Work (Boston, 1904): octagonal tool steel or old files forged about 5 in. long, flat chisels 3/8 to 1 in. with a 60 degree edge, plus gouges, side, cape, diamond-point and round-nose chisels; only the last 1/8 in. of the edge hardened, tempered light purple for steel or dark purple for iron.
Дунд шат
Two or three days for the set

Зааварчилгаа

1

His sizes

Jupyter дэвтэр ачаалж байна…
2

Read Griswold

"When the tool is forged the edge only must be hardened for about 1/8 in., the metal above being left softer to withstand the shock."
3

Forge the blanks

From octagonal tool steel (or old files) forge each chisel about 5 in. (127 mm) from head to edge with a gradual taper to the edge, and forge the head down so it does not broom. Forging steps are ours: forge at a bright red only, as in his part I.

Энэ алхмын материал:

Найман талт багажийн ган савааНайман талт багажийн ган саваа1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дархны хавчаарДархны хавчаар
4

Shape the edges

Flat chisels 3/8, 1/2, 5/8 and 1 in. wide; gouges 1/4-5/8 in. with the bevel inside; side chisels 1/4, 3/8, 1/2 in. with the edge in one flat side; cape chisels 3/16 and 1/4 in. with the stock behind slightly thinner; a diamond point about 1/8 in. on the square (bent version for flat work); round-nose chisels, heavy and a long-tapered drawing chisel (his fig. 1).

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дүрд (гар дүрд)Дүрд (гар дүрд)
5

Harden the edge only

Heat the edge and harden only about 1/8 in. (3 mm) of it in water, leaving the body softer: a chisel hard too far up cracks off on a line under a heavy blow.

Энэ алхмын материал:

УсУс1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
Дархны хавчаарДархны хавчаар
ХувинХувин
6

Temper purple

Brighten the edge with emery cloth and let the heat run the colour down: light purple (530 F) for chisels used on steel, dark purple (550 F) for cast and wrought iron; then cool.

Энэ алхмын материал:

Эмерийн даавууЭмерийн даавуу1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

ХувинХувин
7

Grind

Grind the flat chisel edges to about 60 degrees (45-75: blunter for heavy work), keeping the edge from blueing.

Шаардлагатай багаж:

Ширээний зүлгүүрШирээний зүлгүүр
8

Troubleshooting

Cold chisel troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" II, **Amateur Work** (Boston), vol. III (1903-04), pp. 304-305 and fig. 1 (checked on the archive.org scan amateurwork03bostrich); temper temperatures from his part I table. Forging heats, metric figures and tools are ours.

Материал

3

Шаардлагатай багаж

7

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...