Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings
Woody

Зохиогч

Woody

9. Арван нэгдүгээр сар 2026NO
10
0
0
0
0

Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings

William Kelly of Hastings, Michigan, received US 24,127, dated 24 May 1859, for a vibrating churn. The tub hangs by straps from studs on a frame and is swung by its handles. A slide partition divides it in two; a dasher is hinged to each side of the partition, and a rod from each dasher's middle hooks onto the still frame. As the tub swings, the rods make the dashers flap, driving the cream against the partition and through openings at its foot from one side to the other. Holes in the dashers, and channels down through the partition, let air into the cream. This rung builds it with a 20-litre bucket hung on its side in a timber frame.
Дунд шат
About 1 day, plus printing

Зааварчилгаа

1

How the dashers flap

Jupyter дэвтэр ачаалж байна…
2

Swinging to work two dashers, before it

Merrill swung a pendulum beside the churn. Kelly swings the tub itself, and the still frame works the dashers.
3

Read US 24,127

"... as the dasher draws near the partition, the space is vacated by the cream passing out through the openings h h h in the partition D alternately from one apartment to the other."
4

Print the guide

A groove for the partition's edge. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
5

Print the box f

A journal box for a dasher. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
6

Frame

From 40 x 40 mm timber cut two rails A 640 mm long, four legs splayed from 150 mm either side of a rail's middle to 360 mm out at the floor, and two stretchers 440 mm long. Screw the legs to the rails' ends so the rails stand 580-620 mm up, 480 mm apart, and screw the stretchers between the leg pairs 130 mm up. Screw two cross pieces B 520 x 40 x 30 mm across the rails' tops 220 mm apart, and an eye bolt (staple g) under each at its middle. Put an M12 bolt through each rail's middle, pointing in, as the studs c.

Энэ алхмын материал:

Зөөлөн мод 70x70 ммЗөөлөн мод 70x70 мм4 ширхэг
#10 x 3" модны шураг#10 x 3" модны шураг24 ширхэг
Нүдэн боолтНүдэн боолт2 ширхэг
Зургаан талт болтны цуглуулгаЗургаан талт болтны цуглуулга2 ширхэг
Хавтгай угаагуурХавтгай угаагуур4 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
ТранспортирТранспортир
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Тохируулгатай түлхүүрТохируулгатай түлхүүр
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
7

Tub C and cover I

Lay a food-grade 20-litre bucket on its side, its lid snapped on. Cut away its wall above a level 100 mm over its axis to open the top, and file the edge smooth. Screw a flat-bar strap 30 x 6 mm to the middle of the bottom and of the lid, rising to 180 mm above the axis, each drilled 13 mm at the top to hook on a stud. Glue a guide upright in the middle of the bottom and of the lid, inside. Screw a hardwood foot G under the bucket and a hardwood handle H on each side at axis height. Cut a plywood cover I 340 x 250 mm with a slot 78 x 24 mm each side of the middle.

Энэ алхмын материал:

20 литрийн хувин20 литрийн хувин1 ширхэг
Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван1 ширхэг
Машины шурагМашины шураг8 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка8 ширхэг
PETG филаментPETG филамент1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Модны шурагМодны шураг6 ширхэг
Фанер хуудасФанер хуудас1 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Хөрөө (лобзик)Хөрөө (лобзик)
Дүрд (гар дүрд)Дүрд (гар дүрд)
Төмөр хөрөөТөмөр хөрөө
Ширээний хавчаарШирээний хавчаар
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
8

Partition D and dashers E

Glue up a hardwood partition D 356 x 231 x 20 mm. Cut three half-round openings h 36 mm across in its foot, 100 mm apart, and drill an 8 mm channel j down from the top edge into each. Screw two journal boxes f on each face 113 mm above the foot, 160 mm apart. Cut two dashers E 100 x 220 mm from 10 mm plywood, drill each with four 24 mm holes i, glue an 8 mm dowel 200 mm long along one long edge as the journal, and glue a small block on top 50 mm from that edge for the rod's hook. Snap the journals into the boxes and slide the partition into its guides.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Фанер хуудасФанер хуудас1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Машины шурагМашины шураг8 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Хөрөө (лобзик)Хөрөө (лобзик)
Хүрзэн өрмийн үзүүрийн багцХүрзэн өрмийн үзүүрийн багц
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Элсэн цаасЭлсэн цаас
Халив иж бүрдэлХалив иж бүрдэл
9

Hang it and fit the rods

Hook the straps over the studs so the tub hangs between the rails. Bend two 6 mm stainless rods with a hook at each end, 224 mm between hooks; put the cover on, pass a rod down each slot and hook it through the dasher's block below and the eye bolt above.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
10

The build in 3D

FreeCAD model of this build, the front half cut away: the frame with its studs, cross pieces and eye bolts, the bucket hung on its straps, the cover, the partition in its guides with its foot openings, the two hinged dashers and their rods. It was checked at five swing angles from -15 to +15 degrees.
Дизайны файлBLENDCC0 - Free
11

Churn

Lift the cover, pour about 8 litres of heavy cream at about 15 °C into the two halves, checked with the thermometer, and put the cover back over the rods. Take a handle and swing the tub steadily about 15 degrees each way; time it. When the butter comes, unhook the rods, lift out the partition and dashers, unhook the tub, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий8 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
12

Troubleshooting

Swinging-tub churn troubleshooting.

Flow

Loading...
13

History and honest limits

**William Kelly** of Hastings, Barry County, Michigan, US 24,127, 24 May 1859. He did not claim working dashers by the churn's swinging as such, only the dashers with the slide partition and rods so joined to the frame. His tub was made cylindrical below the centre and flat on two sides; ours is a bucket on its side. He gave no sizes: every size and material and the 15 degree swing are ours.

Материал

19

Шаардлагатай багаж

18

Загварын файлууд

3

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...