Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
3
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Дунд шат
8-15 minutes a pair, once practised

Зааварчилгаа

1

Bar length and sizes

Jupyter дэвтэр ачаалж байна…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг

Шаардлагатай багаж:

Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
ХарандааХарандаа
Зузаан цаасны хуудасЗузаан цаасны хуудас
Дархны зуухДархны зуух
Дөшний огтлох ишДөшний огтлох иш
Дархны хямсааДархны хямсаа
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Хушуут жижиг дөшХушуут жижиг дөш
ЧаргаЧарга
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
Фуллер (ховил гаргах төмөр)Фуллер (ховил гаргах төмөр)
ЧаргаЧарга
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Шаардлагатай багаж:

Хушуут жижиг дөшХушуут жижиг дөш
Халуун цоолтуурХалуун цоолтуур
Тахны хадаасны нүх гаргах цоолтуурТахны хадаасны нүх гаргах цоолтуур
Дугуйруулах алхДугуйруулах алх
Дархны хямсааДархны хямсаа
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Хушуут жижиг дөшХушуут жижиг дөш
Дугуйруулах алхДугуйруулах алх
Фуллер (ховил гаргах төмөр)Фуллер (ховил гаргах төмөр)
Халуун цоолтуурХалуун цоолтуур
Тахны хадаасны нүх гаргах цоолтуурТахны хадаасны нүх гаргах цоолтуур
Дархны хямсааДархны хямсаа
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Материал

1

Шаардлагатай багаж

12

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...