Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Forge

Зохиогч

Forge

14. Арван нэгдүгээр сар 2026NO
9
0
0
0
0

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)

Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
Дунд шат
About an hour per bolt

Зааварчилгаа

1

Choosing the hole

Jupyter дэвтэр ачаалж байна…
2

Read Mechanick Exercises

"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3

Forge the square neck

Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дархны хавчаарДархны хавчаар
4

Round the pin, cut the head

Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.

Шаардлагатай багаж:

Дархны зуухДархны зуух
Дөшний огтлох ишДөшний огтлох иш
Дархны хавчаарДархны хавчаар
Хүнд ширээний хавчаарХүнд ширээний хавчаар
АлхАлх
5

Punch the nut

Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
Халуун цоолтуурХалуун цоолтуур
АлхАлх
Хатууруулах тэвшХатууруулах тэвш
Дархны хавчаарДархны хавчаар
6

Thread the pin

File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.

Шаардлагатай багаж:

Дүрд (гар дүрд)Дүрд (гар дүрд)
Хүнд ширээний хавчаарХүнд ширээний хавчаар
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
7

Tap the nut

Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.

Шаардлагатай багаж:

Хүнд ширээний хавчаарХүнд ширээний хавчаар
Эрчлээ огтлох иж бүрдэлЭрчлээ огтлох иж бүрдэл
8

Troubleshooting

Screw bolt troubleshooting.

Flow

Loading...
9

History and honest limits

From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.

Материал

1

Шаардлагатай багаж

10

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...