Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame
Buttercup

Зохиогч

Buttercup

9. Арван нэгдүгээр сар 2026IE
10
0
0
0
0

Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame

Andrew Patterson of Birmingham, Pennsylvania, received US 23,111, dated 1 March 1859, for a churn whose fan wheel only strikes the surface of the cream. Turned fast through a pulley, it throws the cream over a partition; the cream sinks and comes back under it. The wheel's chamber is also the churn's lid and rests on a jointed frame that works like a parallel rule, so a handle sets the fan to dip about 1/8 in. into whatever quantity of cream is in the box. This rung builds it in pine with a belt-driven printed fan.
Дунд шат
About 8 hours, plus printing

Зааварчилгаа

1

Setting the rest for the cream you have

Jupyter дэвтэр ачаалж байна…
2

A dasher that adjusts to the tub, before it

Fiester's blades spread to fit his tub. Patterson moves his whole fan up and down to the cream's surface.
3

Read US 23,111

"... the rest o, o, w, v, v, is raised or lowered until when b is placed on it the buckets or fans will dip about one-eighth of an inch into the cream and the crank is turned rapidly in such manner that the wheel shall impel the milk or cream which it strikes in the direction of w".
4

Print the hub

The fan's hub with eight square sockets for the arms. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
5

Print the bucket y

A curved bucket for an arm pair's ends. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
6

Box a

From 18 mm pine make an oblong box open at the top, 600 x 300 mm and 320 mm deep inside: floor 636 x 336 mm, sides 636 x 320 mm, ends 300 x 320 mm, glued and screwed.

Энэ алхмын материал:

Нарсан банзНарсан банз2 ширхэг
Модны цавууМодны цавуу1 ширхэг
Модны шурагМодны шураг30 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
ХавчааруудХавчаарууд
Элсэн цаасЭлсэн цаас
Халив иж бүрдэлХалив иж бүрдэл
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
7

The parallel rest v v o o w

Cut two hardwood uprights o 30 x 13 x 190 mm and pin each to a side of the box with an 8 mm bolt 22 mm above the inside floor, 100 mm from the right end. Cut a pine division board w 228 x 170 mm and pin its foot to two hardwood blocks on the floor 200 mm from the left end, so it stands 16 mm clear of the floor. Cut two hardwood bars v 20 x 20 x 340 mm and pin them to the uprights' tops and w's top corners, 300 mm apart, with 160 mm between each foot and top pivot, so the bars stay level as the frame leans. Screw a hardwood handle h i 30 x 12 mm to the left end of one bar, long enough to stand 100 mm above the rim, and bend a flat-bar frame e over the rim to hold it with a pin through holes drilled every 20 mm in the handle.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
Нарсан банзНарсан банз1 ширхэг
Машины шурагМашины шураг8 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка8 ширхэг
Хавтгай угаагуурХавтгай угаагуур16 ширхэг
Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван1 ширхэг
Модны шурагМодны шураг6 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Төмөр хөрөөТөмөр хөрөө
Ширээний хавчаарШирээний хавчаар
Дүрд (гар дүрд)Дүрд (гар дүрд)
Тохируулгатай түлхүүрТохируулгатай түлхүүр
8

Chamber b and the fan

From pine make chamber b open below: two sides 360 x 270 mm, two ends 234 x 270 mm and a top 360 x 270 mm, 270 mm wide outside so it sits on the bars inside a. Drill both sides 12.5 mm for the fan shaft 40 mm up from b's lower edge and 230 mm from its left end, and one side again 170 mm above that for the crank shaft. Cut the 12 mm stainless rod to 285 mm for the fan. Push eight hardwood arms 18 x 18 x 69 mm into the hub's sockets, screw a bucket across each pair of arm ends, slide the hub onto the shaft inside b and fix it with an M4 screw across.

Энэ алхмын материал:

Нарсан банзНарсан банз2 ширхэг
Модны цавууМодны цавуу1 ширхэг
Модны шурагМодны шураг20 ширхэг
Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
PETG филаментPETG филамент1 ширхэг
Машины шурагМашины шураг9 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка9 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Гар хөрөөГар хөрөө
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Халив иж бүрдэлХалив иж бүрдэл
9

Pulleys f and c, crank t

Cut a pulley f 240 mm across and a pulley c 60 mm across from 12 mm plywood, each with a 3 mm flange glued on the outer face, and file a groove round each rim for the cord. Fix c on the fan shaft outside b. Run a 12 mm stainless stub shaft through b's side 170 mm above, fix f on it and a hardwood crank arm 24 x 10 x 112 mm with a 24 mm dowel handle 80 mm long beyond it, out over the side of a. Tie a loop of 6 mm cotton cord round both pulleys.

Энэ алхмын материал:

Фанер хуудасФанер хуудас1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Хөвөн олсХөвөн олс1 m
Машины шурагМашины шураг2 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка2 ширхэг

Шаардлагатай багаж:

Хөрөө (лобзик)Хөрөө (лобзик)
Дүрд (гар дүрд)Дүрд (гар дүрд)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Төмөр хөрөөТөмөр хөрөө
Халив иж бүрдэлХалив иж бүрдэл
10

The build in 3D

FreeCAD model of this build, the near side of both boxes cut away: box a, the uprights, division board and bars of the parallel rest leaning 50 degrees, chamber b on the bars, the fan with its buckets, pulleys f and c, the crank, and handle h i in its frame e. The cord is not drawn.
Дизайны файлBLENDCC0 - Free
11

Churn

Pour in about 14 litres of heavy cream at about 15 °C, checked with the thermometer. Set chamber b on the bars and move the handle until the buckets just dip into the cream, about 3 mm, then pin it in frame e (the notebook gives the lean for other quantities). Turn the crank fast and time it: the fan throws cream over the division board and it returns under it. When the butter comes, lift b off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий14 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
12

Troubleshooting

Surface dash-wheel churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Andrew Patterson** of Birmingham, Allegheny County, Pennsylvania, US 23,111, 1 March 1859, "Churn". He held that a fast fan at the surface does more than a submerged wheel, which has to lift the whole cream, and that it also gathers the butter on the far side of the partition. He claimed box a with chamber b serving as its lid and as the frame for the dash wheel and crank. His only figure is the 1/8 in. dip; every size and material here is ours.

Материал

16

Шаардлагатай багаж

17

Загварын файлууд

3

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...