Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Anvil Hole Punch: Forged C-Frame With a Steel Die Block and Top Die, Set in the Hardy Hole (Richardson, 1889)
Forge

Зохиогч

Forge

14. Арван нэгдүгээр сар 2026NO
7
0
0
0
0

Anvil Hole Punch: Forged C-Frame With a Steel Die Block and Top Die, Set in the Hardy Hole (Richardson, 1889)

A blacksmith's anvil punch from Richardson's Practical Blacksmithing (1889): a bent C-frame of Swedish iron with a steel die block welded on, a square shank that drops into the anvil's hardy hole, and a cast-steel top die struck with a sledge. A set of six, 1/4 to 1 in, punches cold iron up to 5/16 or 3/8 in thick.
Дээд шат
About 1 day

Зааварчилгаа

1

The set of six

Jupyter дэвтэр ачаалж байна…
2

Read Practical Blacksmithing

"I think every blacksmith should have a set of them."
3

Forge the frame and die block

Take Swedish iron 1-1/2 by 3/4 by 10 in, upset one end a little, and weld a square of good steel 1-1/2 by 1-1/2 in firmly on it. Punch a hole in the centre of the steel a little larger than the hole to be cut, driving from the iron side so the hole is largest at the bottom and the slugs drop out. Heat the other end, cut it half off 1-1/2 in from the end, bend it over and weld it, then punch and work out a perfectly true 3/4 in square hole (Fig. 68).

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг
Багажийн ган савааБагажийн ган саваа1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дархны хямсааДархны хямсаа
Халуун цоолтуурХалуун цоолтуур
Халуун цүүцХалуун цүүц
Том алхТом алх
4

Weld on the shank

Weld an iron the size of your anvil's square hole on the bottom side, 2-1/2 in from the round hole (Fig. 69). File and dress the piece.

Энэ алхмын материал:

Давтсан төмөр гулдмайДавтсан төмөр гулдмай1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дүрд (гар дүрд)Дүрд (гар дүрд)
5

Make the top die

Cut 6 in of 3/4 in square cast steel, draw it down and file one end to fit the round hole; for the 1/4 in punch make the round part 5/16 in long, larger for larger punches (Fig. 70).

Энэ алхмын материал:

Багажийн ган савааБагажийн ган саваа1 ширхэг

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Дүрд (гар дүрд)Дүрд (гар дүрд)
Төмөр хөрөөТөмөр хөрөө
6

Bend, fit and temper

Heat the frame and bend it so the two holes line up; fit the top die and make sure it enters the hole perfectly true. Let it cool slowly, check the bottom die face and that the die works straight and easily, then temper as for any tool that cuts iron (Fig. 71).

Шаардлагатай багаж:

Дархны зуухДархны зуух
ДөшДөш
АлхАлх
Хатууруулах тэвшХатууруулах тэвш
7

Troubleshooting

Anvil punch troubleshooting.

Flow

Loading...
8

History and honest limits

From M. T. Richardson (ed.), **Practical Blacksmithing**, vol. I (1889), "Making an Anvil Punch" by N. C. M. (checked on the archive.org scan practicalblacksm00richrich, pp. 126-128). He gives no temper colour; the tools and metric figures are ours.

Материал

2

Шаардлагатай багаж

10

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...