Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Butterfly-Wing Churn: Two Dashers Hinged to an Adjustable Bar Flap Together From One Crank
Woody

Зохиогч

Woody

9. Арван нэгдүгээр сар 2026NO
9
0
0
0
0

Butterfly-Wing Churn: Two Dashers Hinged to an Adjustable Bar Flap Together From One Crank

Josiah Stubbs of Dublin, Indiana, received US 24,673, dated 5 July 1859, for a churn with two dashers hinged to a central bar like a butterfly's wings. The bar slides on notched stays inside the shell and is set so the cream barely covers it. One crank on the side works both dashers through two rods, one crossing the churn on a slant. Going down, the cream rushes round the dashers' edges against the shell; going up, flanges on the dashers carry cream up and throw it together. This rung builds it in a 20-litre bucket.
Дунд шат
About 6 hours, plus printing

Зааварчилгаа

1

Setting the bar for the cream you have

Jupyter дэвтэр ачаалж байна…
2

Hinged, flapping dashers, before it

Kelly flapped hinged dashers by swinging the tub. Stubbs keeps the shell still and flaps them from a crank.
3

Read US 24,673

"As the dashers are drawn upwardly, a portion of the fluid will be retained upon them, by means of the flanges (e) and thrown violently together as the dashers reach their upper extremity of motion".
4

Print the flange

A quarter of a dasher's flange e. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Дизайны файлSTLCC0 - Free
5

Stays and bar b

Screw two hardwood stays a 24 x 15 mm, 337 mm long, upright inside the bucket on opposite sides, and saw notches a' 6 mm wide and 4 mm deep in their inner faces every 20 mm from 60 to 220 mm up. Cut a hardwood bar b 272 x 20 x 16 mm with a slotted block 44 mm wide at each end to slide on the stays, and fit an M5 set screw c with a wing nut through one block to hold it in a notch.

Энэ алхмын материал:

20 литрийн хувин20 литрийн хувин1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Модны шурагМодны шураг6 ширхэг
Модны цавууМодны цавуу1 ширхэг
Машины шурагМашины шураг1 ширхэг
Эрвээхэй гайкаЭрвээхэй гайка1 ширхэг
Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг

Шаардлагатай багаж:

Гар хөрөөГар хөрөө
Модны цүүцнүүдМодны цүүцнүүд
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Халив иж бүрдэлХалив иж бүрдэл
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
6

Dashers d d

Cut two half-discs 244 mm across from 12 mm plywood and trim each to 220 mm along its straight edge. Glue the printed flanges e round their curved edges, standing 15 mm up. Hinge each dasher's straight edge to one side of the bar with two stainless butt hinges, 4 mm clear of the bar. Screw a small hardwood eye block on each dasher 100 mm out from the bar's middle, the right one 30 mm toward the front, the left one 40 mm toward the back.

Энэ алхмын материал:

Фанер хуудасФанер хуудас1 ширхэг
PETG филаментPETG филамент1 ширхэг
Модны цавууМодны цавуу1 ширхэг
Хаалганы нугасХаалганы нугас4 ширхэг
Модны шурагМодны шураг16 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг

Шаардлагатай багаж:

FDM 3D хэвлэгчFDM 3D хэвлэгч
Хөрөө (лобзик)Хөрөө (лобзик)
Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Элсэн цаасЭлсэн цаас
Халив иж бүрдэлХалив иж бүрдэл
7

Crank h k and rods g g'

Drill the bucket's wall 13 mm 315 mm up, 30 mm toward the front, and fit a 12 mm stainless shaft through a hardwood bearing block outside, sealed. Fix a hardwood crank arm h 35 mm between centres on the inner end with a 8 mm pin pointing inward, and a crank handle k outside. Bend two 6 mm stainless rods with an eye at each end: g 185 mm between eyes from the pin to the right dasher, g' 262 mm from the pin across the churn on a slant to the left dasher.

Энэ алхмын материал:

Зэвэрдэггүй ган савааЗэвэрдэггүй ган саваа1 ширхэг
Хатуу модон банзХатуу модон банз1 ширхэг
Хатуу модон гадасХатуу модон гадас1 ширхэг
Силиконон битүүлэгчСиликонон битүүлэгч1 ширхэг
Машины шурагМашины шураг2 ширхэг
Нейлон оруулгатай тогтоох гайкаНейлон оруулгатай тогтоох гайка2 ширхэг

Шаардлагатай багаж:

Утасгүй өрөмУтасгүй өрөм
Өрмийн үзүүрийн иж бүрдэлӨрмийн үзүүрийн иж бүрдэл
Ширээний хавчаарШирээний хавчаар
Төмөр хөрөөТөмөр хөрөө
Дүрд (гар дүрд)Дүрд (гар дүрд)
Халив иж бүрдэлХалив иж бүрдэл
8

The build in 3D

FreeCAD model of this build, the near side of the bucket cut away: the notched stays, bar b, the two hinged dashers with their flanges, the crank inside the wall and the two rods, one crossing on a slant. It was checked at eight crank angles.
Дизайны файлBLENDCC0 - Free
9

Churn

Pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and set the bar in the notch the notebook gives so the cream barely covers it. Put the lid on and turn the crank steadily; time it. When the butter comes, lift the bar and dashers out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Энэ алхмын материал:

Өтгөн цөцгийӨтгөн цөцгий8 l
Бүдүүн далайн давсБүдүүн далайн давс1 ширхэг
УсУс1 ширхэг

Шаардлагатай багаж:

Дотор нь үлдээдэг мэдрэгчтэй термометрДотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигчСекунд хэмжигч
Дижитал гал тогооны жинДижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аягаЗэвэрдэггүй ган том хольц аяга
10

Troubleshooting

Butterfly-wing churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Josiah Stubbs** of Dublin, Wayne County, Indiana, US 24,673, 5 July 1859, "Churn". He claimed working the butterfly wings with a single crank on one side, the rod g' crossing the cylinder on a slant. He gave no sizes or materials: every size, the notches' spacing and the crank's throw are ours.

Материал

16

Шаардлагатай багаж

16

Загварын файлууд

2

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...