Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)
Forge

Зохиогч

Forge

13. Арван нэгдүгээр сар 2026NO
8
0
0
0
0

Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)

T. T. Sturgeon's hand plow from The Boy Mechanic, Book 3 (1919), "worth about $5 at an outlay of 25 cents": a 16 in wheelbarrow wheel, handles ripped from one spruce strip, iron-strap braces, an adjustable vertical strap, and a moldboard and share cut from an old shovel blade to his grid pattern.
Дунд шат
About 1 day

Зааварчилгаа

1

His cut list in centimetres

Jupyter дэвтэр ачаалж байна…
2

Read The Boy Mechanic, Book 3

"The labor of spading a garden of even moderate size is sufficient to warrant the person who undertakes the job in making a hand plow like that shown in the illustration."
3

Make the handles

Mark both handles on a 7/8 by 4 in spruce strip 5 ft long, one curved grip at each end on opposite edges. Cut the curves with a keyhole saw, then rip the board into the two handles; smooth them and trim the grips with a sharp knife. Cut a section of broomstick for the upper brace.

Энэ алхмын материал:

Хатуу модон банзХатуу модон банз1 ширхэг
ШүүрШүүр1 ширхэг

Шаардлагатай багаж:

Муруй хөрөөМуруй хөрөө
Уртааш хөрөөУртааш хөрөө
Арьсны хутгаАрьсны хутга
ХарандааХарандаа
4

Make the iron parts

Lower brace: iron 1/4 by 1-1/4 by 12 in, drilled for 1/4 in bolts, bent at right angles 1-1/2 in from each end, with a 1/4 in hole at the middle. Vertical support: 1/4 by 1-1/4 by 18 in, four 1/4 in adjusting holes 1 in apart at the top, three 1/4 in holes at the bottom for the moldboard, and a 5/16 in hole at the 7-1/2 in mark. Two braces 14 in long of 1/4 by 1-1/4 in, a 3/8 in hole at the front of each for the 3/8 by 10 in axle bolt and a 5/16 in hole at the other end, each 1 in from the end. Landside: 1/8 by 3/4 by 12 in.

Энэ алхмын материал:

Зөөлөн ганы хавтгай туйванЗөөлөн ганы хавтгай туйван3 ширхэг

Шаардлагатай багаж:

Төмөр хөрөөТөмөр хөрөө
Гар өрөмГар өрөм
Ширээний хавчаарШирээний хавчаар
АлхАлх
Дүрд (гар дүрд)Дүрд (гар дүрд)
Соронзон хэмжих туузан шугамСоронзон хэмжих туузан шугам
5

Cut the moldboard

Draw his moldboard (Fig. 4) on cardboard ruled in 1 in squares, tracing the outline square by square, and mark the bolt holes. Trace it on an old shovel blade, using the thickest part for the point of the share. Cut it out, smooth the edges and sharpen the cutting edge. Drill for 1/4 in bolts to the vertical strap and 3/16 in bolts to the landside.

Энэ алхмын материал:

ХүрзХүрз1 ширхэг
Картон загварын хуудасКартон загварын хуудас1 ширхэг

Шаардлагатай багаж:

ХарандааХарандаа
Төмөр хөрөөТөмөр хөрөө
Өнцгийн зүлгүүрӨнцгийн зүлгүүр
Дүрд (гар дүрд)Дүрд (гар дүрд)
Гар өрөмГар өрөм
6

Shape and assemble

Curve the moldboard and fit it to the supports as in Figs. 1-3. Bend the 12 in landside strip under the moldboard and bolt it on. Assemble on the 16 in wheel and 3/8 in axle bolt, with wheel and landside in line (Fig. 2) and the landside's rear edge raised slightly (Fig. 3); set the vertical strap's height for the operator in its adjusting holes. Paint the plow and oil the smoothed cutting parts.

Энэ алхмын материал:

Дугуйт тэргэнцрийн дугуйДугуйт тэргэнцрийн дугуй1 ширхэг
Дугуй толгойт боолтДугуй толгойт боолт6 ширхэг
Зургаан талт эрэгЗургаан талт эрэг6 ширхэг
Хавтгай угаагуурХавтгай угаагуур6 ширхэг
Тосон будагТосон будаг1 ширхэг
Машины тосМашины тос1 ширхэг

Шаардлагатай багаж:

Ширээний хавчаарШирээний хавчаар
АлхАлх
Өргөн будгийн бийрӨргөн будгийн бийр
7

Troubleshooting

Garden plow troubleshooting.

Flow

Loading...
8

History and honest limits

From "Garden Plow Made of Pick-Up Material" by T. T. Sturgeon, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 227-228). The moldboard shape is his Fig. 4 grid. The keyhole saw is a coping saw here; the tools and metric figures are ours.

Материал

11

Шаардлагатай багаж

12

Холбоотой загварууд

Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...