Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)
Forge

Зохиогч

Forge

4. Арван нэгдүгээр сар 2026NO
8
0
0
1
0

Watering Can: the Tinplate Rose Watering-Can (Hasluck, 1907)

A tinsmith's garden watering can: a round body from one sheet 2 ft 1 in x 8 1/2 in, a two-piece spout with a perforated rose, a hollowed top with a cross handle, and a back handle with a thumb ring. Tinplate or galvanised iron. Variable: the rose. Its pattern diameter is the rose diameter x 4 / 3; finer holes for seedlings. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 54-57. Unknown: solder. Picture: Figs. 132-135 of the book.
Дунд шат
Unknown

Зааварчилгаа

1

Make the body and bottom

Cut a sheet 2 ft 1 in by 8 1/2 in. Wire one edge, sink it in the crease iron, round it and groove the seam; solder the seam inside. Cut the spout hole opposite the seam, 2 1/2 in from the bottom. Edge the bottom to fit, beat it up and solder it from inside.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 body, bottom
Төмөр утасТөмөр утас1 edge
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
ГадасГадас
Модон алхМодон алх
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
2

Make and fit the spout

Cut the spout in two pieces (Fig. 133), bend them to shape and solder the seams. Solder the larger piece into the body. Make it longer for plants out of reach, with an elbow for plants up high. Make the stay: a taper strip as long as the gap between can and spout, bent to a half-round section and soldered in.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 spout, stay
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
ГадасГадас
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
3

Make the rose

Set out the rose body (Fig. 135): its diameter is the rose diameter x 4 / 3, so a 3 in rose needs a 4 in pattern, with lines a b at right angles. Bend it over a funnel stake and solder the seam. Hollow a disc for the front, with edges for capping on. Inside the hollow, mark circles and pierce them at intervals with a bradawl over a hard wood block; very fine for seedlings. Solder front and stem to the rose body. Several roses of different sizes are useful.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 rose
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 ширхэг

Шаардлагатай багаж:

Хоёр үзүүрт циркульХоёр үзүүрт циркуль
Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
ГадасГадас
Тэгшлэх алхТэгшлэх алх
ШөвөгШөвөг
Хатуу модны блокХатуу модны блок
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
4

Fit the top and handles

Hollow the top (Fig. 134), fit it to the body, wire its inner arc and solder it on. Cross handle: a strip about 1 3/4 in wide, wired with No. 12 B.W.G., bent to shape; cut two holes in the top with a small sharp chisel and solder the ends inside and on top. Back handle (Fig. 136): wire and bend it, solder a small boss under its upper part, and solder it opposite the spout with a thumb ring at the top. Solder three small hollowed studs under the bottom.

Энэ алхмын материал:

Цагаан тугалган хуудасЦагаан тугалган хуудас1 top, handles, studs
Төмөр утасТөмөр утас1 No. 12 B.W.G.
Цагаан тугалга-хар тугалганы гагнуурЦагаан тугалга-хар тугалганы гагнуур1 ширхэг

Шаардлагатай багаж:

Тугалган цаас огтлох хайчТугалган цаас огтлох хайч
Тэгшлэх алхТэгшлэх алх
Ган цүүцГан цүүц
Цахилгаан гагнуурын индүүЦахилгаан гагнуурын индүү
ФлюсФлюс
5

Clean and paint

Clean with turpentine and whiting. Give two good coats of paint: red inside and green outside suit it.

Энэ алхмын материал:

Тосон будагТосон будаг2 coats

Шаардлагатай багаж:

СкипидарСкипидар
Кальцийн карбонат (цагаан шохой)Кальцийн карбонат (цагаан шохой)

Материал

4

Шаардлагатай багаж

12

Энэ загвараар хийдэг

CC0 Нийтийн домэйн

Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.

Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

Хэлэлцүүлэг

(0)

Нэвтрэх хэлэлцүүлэгт нэгдэхийн тулд

Сэтгэгдлүүдийг ачаалж байна...