Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ

Rubber-Pipe Pump Churn: A Pulley Rolls Milk Through a Tube in a Ring and Jets It Through Gauze
Loren J. Wicks of Racine, Wisconsin, received US 24,686, dated 5 July 1859, for a churn that is a rolling-tube pump. An india-rubber pipe runs from the bottom of the milk box once round the groove inside a ring and up into a smaller box on top. A pulley on a fast crank rolls round the ring on the pipe and drives the milk up in a stream against two gauze partitions hung under the top box's cap. The broken milk runs back through a screen of fine wooden strips into the box below, the butter staying behind; the stream keeps going until all the butter is out.
This rung builds it with silicone tubing, a printed ring and pulley, and pine boxes.
Дунд шат
About 1 day, plus printing
Зааварчилгаа
1
1
A rolling pulley as a pump
A rolling pulley as a pump
Jupyter дэвтэр ачаалж байна…
2
2
A churn that pumps the cream round, before it
A churn that pumps the cream round, before it
McClintock pumped with a vane and valves. Wicks squeezes a rubber pipe and needs no valve at all.
3
3
Read US 24,686
Read US 24,686
"Thus it will plainly be seen that in the manner which pipe (B) passes round circular frame (F) the pulley when rolling on it will force the milk up into box (C)."
4
4
Print the frame F
Print the frame F
The ring with the tube's groove round its inside and the hole in its foot. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
5
5
Print the rotor
Print the rotor
The hub with the two projections that carry the pulley. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
6
6
Print the pulley H
Print the pulley H
The pulley that rolls on the tube. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
7
7
Stand and boxes
Stand and boxes
From pine make box A 360 x 240 mm inside and 230 mm deep, and stand it on four 44 mm legs 400 mm tall. Drill a 13 mm hole near the front of its floor. Make box C 360 x 122 mm inside and 180 mm deep, with a floor, and stand it on two cleats across A's back, leaving A open for 100 mm in front of it. Cut C's front out between 18 and 122 mm up and glue hardwood strips 6 mm wide upright in the opening, 4 mm apart, as screen D. Drill C's front 13 mm above the screen for a 8 mm stainless spout.
Энэ алхмын материал:
Нарсан банз3 ширхэг
Зөөлөн мод 70x70 мм2 ширхэг
Модны цавуу1 ширхэг
Модны шураг40 ширхэг
Хатуу модон банз1 ширхэг
Зэвэрдэггүй ган хоолой1 ширхэгШаардлагатай багаж:
Гар хөрөө
Хөрөө (лобзик)
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Хавчаарууд
Элсэн цаас
Соронзон хэмжих туузан шугам8
8
Cap I and partitions E
Cap I and partitions E
Cut a plywood cap 340 x 100 mm to slide on C's top. Make two frames 240 x 138 mm from 3 mm plywood with a window in each, staple stainless mesh over the windows (for his tin and gauze), and screw them upright under the cap 40 mm apart, across the jet's path.
Энэ алхмын материал:
Фанер хуудас1 ширхэг
Утсан тор1 ширхэг
Модны шураг8 ширхэгШаардлагатай багаж:
Хөрөө (лобзик)
Тугалган цаас огтлох хайч
Халив иж бүрдэл9
9
Frame F, pulley and pipe B
Frame F, pulley and pipe B
Screw a pine board across the front legs below box A and screw the printed frame F on its front, 220 mm up. Bore the board for a 12 mm stainless shaft G with a hardwood support K behind it, fit the rotor and pulley H on its pin inside the frame and a hardwood crank P outside. Push 12 x 8 mm silicone tubing into A's floor hole, sealed, down through a hole in the board and the hole in F's foot, once round the groove, out through the same hole, round the outside of F and up to C's spout.
Энэ алхмын материал:
Нарсан банз1 ширхэг
PETG филамент1 ширхэг
Зэвэрдэггүй ган саваа2 ширхэг
Хатуу модон банз1 ширхэг
Хатуу модон гадас1 ширхэг
Машины шураг3 ширхэг
Нейлон оруулгатай тогтоох гайка3 ширхэгШаардлагатай багаж:
FDM 3D хэвлэгч
Утасгүй өрөм
Өрмийн үзүүрийн иж бүрдэл
Төмөр хөрөө
Ажлын хутга
Халив иж бүрдэл10
10
The build in 3D
The build in 3D
FreeCAD model of this build, half the boxes cut away: box A on its stand, box C with screen D, the cap and the two mesh partitions, the board with frame F, the rotor and pulley on the shaft, the crank, and the tube's run from A's floor round the ring and up to C. The rotor was checked at six angles.
11
11
Churn
Churn
Pour about 10 litres of cream at about 15 °C into box A, checked with the thermometer. Turn the crank fast and time it: a stream jets into C against the mesh and runs back through the screen. Slide the cap back and forth now and then. When the butter is held in C, stop, lift C off, take the butter out, pour the buttermilk from A, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Энэ алхмын материал:
Өтгөн цөцгий10 l
Бүдүүн далайн давс1 ширхэг
Ус1 ширхэгШаардлагатай багаж:
Дотор нь үлдээдэг мэдрэгчтэй термометр
Секунд хэмжигч
Дижитал гал тогооны жин
Зэвэрдэггүй ган том хольц аяга12
12
Troubleshooting
Troubleshooting
Rubber-pipe pump troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Loren J. Wicks** of Racine, Wisconsin, US 24,686, 5 July 1859, "Churn". He did not claim forcing milk in a stream against a substance as such, only boxes A and C with pipe B, and box C with screen D and the hanging partitions E. His pipe was india rubber and his partitions tin and gauze; our silicone tubing, mesh frames, printed ring and pulley and every size are ours.
Материал
18- 3 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 48 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 2 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 3 ширхэгТүр орлуулагч
- 3 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 10 lТүр орлуулагч
- 1 ширхэгТүр орлуулагч
- 1 ширхэгТүр орлуулагч
Шаардлагатай багаж
16- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- 1 vendor sell this, none ship to you yetТүр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
Загварын файлууд
4Энэ загвараар хийдэг
Холбоотой загварууд
Эдгээр загварууд мэдлэг хуваалцдаг — арга техник, материал эсвэл зарчим

Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition
Martin зохиосон
Мод боловсруулалт
10
0
0
0
0
0

Funnel-Tube Atmospheric Churn: Trailing Funnels on a Fast Cross Draw Air Down Slanting Tubes Into the Cream
Buttercup зохиосон
ХООЛ БА УНДАА
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef зохиосон
ГАРААР ХИЙСЭН
63
0
0
0
0
0
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.

