Хамтын ажиллагаа
УРЛАГ
ГОО САЙХАН БА ЭРҮҮЛ МЭНД
ГАРААР ХИЙСЭН
СОЁЛ БА ТҮҮХ
ҮЗВЭР НААДАМ
БАЙГАЛЬ ОРЧИН
ХООЛ БА УНДАА
УРВУУ ИНЖЕНЕРЧЛЭЛ
ШИНЖЛЭХ УХААН
СПОРТ
ТЕХНОЛОГИ
ӨМСДӨГ ХЭРЭГСЭЛ
Wood Lathe: Simple Amateur's Lathe with a Maple Bed, 7 in Swing (Lathe Work for Beginners, 1922)
A wood-turning lathe an amateur can build: two strips of hard maple bolted to maple legs make the 3 ft bed, and cast-iron head-stock, tail-stock, hand-rest body, hand wheels and cone pulleys are cast from home-made patterns. Steel spindles turn in the cast-iron bearings, and a cone pulley drives the head-stock from a countershaft.
Result: a wood lathe with a 7 in swing and a 3 ft bed.
Source: R. F. Yates, Lathe Work for Beginners (1922), Chapter XII, pp. 208-216. Unknown: the pattern sizes (on the book's drawings) and the drive. Picture: Fig. 157 of the book.
Дээд шат
Unknown
Зааварчилгаа
1
1
Make the patterns and get castings
Make the patterns and get castings
Make patterns from any handy wood: one for both head-stock and tail-stock, with a web joining the two bearings so the casting does not spring; one for the hand wheels (three castings); one for the washers (two); the cone pulley (two: lathe and countershaft); and the hand-rest body. Give them a slight draw taper. Have them cast in iron at a foundry. Not given: pattern sizes (on the book's drawings).
Энэ алхмын материал:
Цутгамал төмөр эдлэл1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyШаардлагатай багаж:
Хөрөөдсөн банз
Вагранка зуух
Тодорхойгүй хэмжээс2
2
Build the maple bed
Build the maple bed
Make the bed of two strips of clear hard maple 1 in thick, 4 in wide and about 36 in long (about 1 1/2 in thick for a longer bed), and two maple legs, the part between the ways cut exactly square. Bore a 5/8 in hole through the head-stock leg in line with the head-stock's 1/2 in tapped hole, recessed below for a nut and washers. Bolt bed to legs with eight 3/8 in carriage bolts. Sand it and give it a coat of clear shellac against warping. White oak will do if there is no maple.
Энэ алхмын материал:
Хатуу модны зузаан банз1 ways and legs
Дугуй толгойт боолт8 3/8 in carriage bolts
Шеллак1 finishШаардлагатай багаж:
Суурин өрөм
Элсэн цаас3
3
Machine the stocks
Machine the stocks
Face the outside ends of the head-stock and tail-stock bearings on a shaper or milling machine. Drill the bearings between centres in a lathe with a 47/64 in drill, saw off the joining web, face the inner ends and ream to 3/4 in. Line both castings up on a 3/4 in shaft and machine their bottoms. Drill oil holes in the head-stock lugs. Tap the tail-stock front lug 3/16 in for a clamp turned, heated and bent to shape, with soft copper or brass under it; tap the tail-stock rear bearing 7/8 in, 9 threads.
Энэ алхмын материал:
Тодорхойгүй металл1 clamp and copper padШаардлагатай багаж:
Фрезийн машин
Металл эрэг
Эрчлээ огтлох иж бүрдэл
Дархны зуух4
4
Turn the spindles and pulley
Turn the spindles and pulley
Turn the head-stock spindle from 1 3/8 in machine steel: 3/4 in diameter, a 7/8 in nose threaded 9 to the inch, a 3/8 in hole right through and a No. 1 Morse taper in the nose. Turn the tail-stock spindle from 7/8 in stock, 3/4 in diameter with a 7/8 in, 9-thread part. Centre each piece, drill halfway from each end with a 3/8 in drill, ream, then finish between centres. Turn the cone pulley with crowned faces, wide enough to run easily between the bearings, and fix it to the spindle with a 3/8 in headless set screw.
Энэ алхмын материал:
Зөөлөн ган дугуй саваа1 spindlesТодорхойгүй металл1 set screwsШаардлагатай багаж:
Металл эрэгСуурин өрөм5
5
Fit the wheels and hand rest, and assemble
Fit the wheels and hand rest, and assemble
Drill hand wheel N 3/4 in for the tail-stock spindle and hold it with a 1/4 in set screw; tap the other two wheels 1/2 in. Drill the washers 9/16 in. Bolt the head-stock down with a stud through the leg, and fit a 1/2 in stud about 7 in long for the tail-stock and a 1/2 in square-headed bolt for the hand-rest body. Plane the hand rest's bottom, drill it 3/4 in, and fit tee-rests of 1/4 x 1 in flat steel welded to 3/4 in shafting, held by a 1/4 in set screw; make several lengths. The cast iron serves as bearing metal, or the bearings can be bushed or babbitted.
Энэ алхмын материал:
Зөөлөн ганы хавтгай туйван1 tee-restsТодорхойгүй металл1 studs, bolts, set screws, shaftingШаардлагатай багаж:
Суурин өрөмЭрчлээ огтлох иж бүрдэлДархны зуухМатериал
7- 1 head-stock, tail-stock, wheels, washers, pulleys, rest bodyТүр орлуулагч
- 1 ways and legsТүр орлуулагч
- 8 3/8 in carriage boltsТүр орлуулагч
- 1 finishТүр орлуулагч
- 1 studs, bolts, set screws, shaftingТүр орлуулагч
- 1 spindlesТүр орлуулагч
- 1 tee-restsТүр орлуулагч
Шаардлагатай багаж
9- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
- Түр орлуулагч
Холбогдсон загварын материал
10% хамаарал
Casting Iron in a Cupola Furnace — Re-Melting Pig Iron into Finished Castings
Piett зохиосон
Металл боловсруулалт
52
0
0
0
6
0
10% хамаарал
Oak Boards and Blocks, Milled and Air-Dried
Woody зохиосон
Мод боловсруулалт
43
0
0
0
3
0
10% хамаарал
Mild Steel Bar Stock Forged from an Ingot
Forge зохиосон
Орчин үеийн
43
0
0
0
5
0
10% хамаарал
Shellac Flakes from Stick Lac
Mary зохиосон
Мод боловсруулалт
33
0
0
0
1
0
10% хамаарал
Screws: Cold Headed and Thread Rolled
Emma зохиосон
Металл боловсруулалт
48
0
0
0
1
0
Энэ загвараар хийдэг
CC0 Нийтийн домэйн
Энэ загвар CC0 дор гаргагдсан. Та зөвшөөрөл авахгүйгээр хуулах, өөрчлөх, түгээх, ашиглах боломжтой.
Загвараар дамжуулан бүтээгдэхүүн худалдаж авч Бүтээгчийг дэмжээрэй Бүтээгчийн шимтгэл Борлуулагчаар тогтоосон, эсвэл энэ загварын шинэ хувилбар үүсгэж орлогоо хуваахын тулд өөрийн загварт холбоос болгон оруулна уу.