ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Fits: Clearance, Transition and Interference — the Difference Is Microns
A shaft that slides into a hole and a shaft that has to be pressed in can differ in diameter by less than the thickness of a human hair. Which of those you have is decided by a few microns, and the difference in behaviour is total.
A CLEARANCE fit always has a gap: the parts assemble by hand and can move. An INTERFERENCE fit always has the shaft larger than the hole: the parts must be forced together and then grip each other permanently. A TRANSITION fit may be either, depending on where the two parts happen to fall in their tolerances.
This is why a bearing can spin on its shaft, or crack its outer ring, or work perfectly — all from the same drawing and the same parts bin. The fit is the design decision, and it is made in numbers before anything is cut.
Intermedio
3 hours
Instrucciones
1
1
Measure both parts, and measure them properly
Measure both parts, and measure them properly
You cannot choose a fit without knowing what you have. Measure the shaft and the bore with a micrometer or a good caliper, at several places along their length and at several angles round them.
Several angles matters because nothing is perfectly round. A shaft that reads 19.98 mm one way and 20.02 mm at ninety degrees is out of round by 0.04 mm, which is larger than most fits — and averaging the two hides it.
Let both parts reach the same temperature first. Steel expands about 11 microns per metre per degree, so a 50 mm part handled for a minute can grow by more than the fit you are trying to measure. Warm hands are a real error here.
Materiales para este paso:
Eje de acero de 30 mm1 piezaHerramientas necesarias:
Calibre vernier
Calibre digital de 6 pulgadas2
2
The arithmetic, and what each fit is for
The arithmetic, and what each fit is for
Cargando el cuaderno de Jupyter…
Materiales para este paso:
Eje de acero de 30 mm1 pieza
Ball Bearing - Non-Flanged (8mm Bore, 22mm OD)1 piezaHerramientas necesarias:
Calibre vernier
Ordenador de sobremesa
Calculadora3
3
Temperature is a tool, not just an error
Temperature is a tool, not just an error
Heat the outer part and it grows; chill the inner part and it shrinks. Do both and an interference fit can be assembled by hand, then locks as the temperatures equalise.
Steel expands about 11 microns per metre per degree Celsius, so a 100 mm bore heated by 100 degrees grows roughly 0.11 mm — far more than any normal interference. An oven at 120 degrees, or a freezer for the shaft, is usually enough.
Never heat a bearing above about 120 degrees. Above that the hardened rings begin to temper and lose hardness permanently, and a blowtorch anywhere near a bearing ruins it in seconds. Induction heaters and hot oil baths exist precisely because the temperature has to be controlled.
Materiales para este paso:
Eje de acero de 30 mm1 piezaBall Bearing - Non-Flanged (8mm Bore, 22mm OD)1 piezaHerramientas necesarias:
Calibre digital de 6 pulgadas
Guantes de nitrilo4
4
Surface finish and roundness are part of the fit
Surface finish and roundness are part of the fit
A measured diameter is an average over a surface that has peaks and valleys. Press two rough surfaces together and the peaks flatten, so the effective interference is less than the measured one — often by 2 to 5 microns on ordinary turned work.
That is why bearing seats are ground rather than turned. It is not fussiness: a rough seat loses a significant fraction of a 15 micron interference to flattened peaks the first time the joint is loaded, and then the bearing creeps.
Roundness matters as much. A bore that is 0.03 mm oval will grip a round shaft at two points and leave gaps at ninety degrees, so the pressure is concentrated rather than shared — which distorts the bearing ring and takes the internal clearance with it.
Materiales para este paso:
Eje de acero de 30 mm1 piezaHerramientas necesarias:
Comparador de cuadranteCalibre vernier
Juego de galgas de espesoresMateriales
2- 1 piezaMarcador de posición
- Ball Bearing - Non-Flanged (8mm Bore, 22mm OD)10% de comisión1 piezaMX$22.35
Herramientas requeridas
7- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Total estimado
Lo que compró quien lo hizo. Los materiales sin precio se consiguen donde tú los compres.
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.