SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
MASA DEPAN HIJAU
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
WEARABLES
Making a Bronze Torc — Twisting and Bending a Neck Ring
Forge

Dicipta oleh

Forge

26. Mei 2026NO
22
0
0
0
0

Making a Bronze Torc — Twisting and Bending a Neck Ring

The torc (torque) was the defining ornament of Bronze Age and Celtic cultures — a rigid open-ended neck ring worn by warriors, chieftains, and gods in the art of the period. From Ireland to Persia, gold and bronze torcs symbolised status, wealth, and divine favour. Some of the most famous examples, like the Snettisham Great Torc, are among the finest metalwork ever produced.

A bronze torc is made by casting a long rod, twisting it while hot to create the characteristic spiral pattern, then bending the twisted rod into a C-shape that fits around the neck. The terminals (ends) are hammered flat and curled into decorative finials, or cast separately and soldered on.

The twist is both decorative and structural — the spiral cross-section is stiffer than a plain round rod of the same weight, allowing the torc to spring open slightly when placed over the head and then grip the neck firmly.

Pertengahan
2-3 hours

Arahan

1

Cast a long bronze rod

Carve a straight groove about 40 cm long and 8 mm wide in a flat stone slab. Pour molten bronze to fill the groove — about 200 g of metal. A square-section groove produces a rod that twists more visibly than a round one. Allow to cool completely and demould.

Bahan untuk langkah ini:

Copper Sheet (0.5-1mm)Copper Sheet (0.5-1mm)180 g
2

Hammer the rod to uniform cross-section

The cast rod will have slight irregularities from the mould surface. Hammer the entire length on a flat stone anvil, rotating 90 degrees between passes, to produce a uniform square cross-section about 6-7 mm per side. Anneal whenever the rod resists hammering.

Alatan diperlukan:

HammerstoneHammerstone
Flat Stone SlabFlat Stone Slab
3

Anneal the rod for twisting

Heat the entire rod in a charcoal fire until it glows dull cherry red along its full length. The rod must be uniformly soft for the twist — a cold spot creates an uneven twist or a kink. Use a long fire bed and rotate the rod to heat evenly.

Bahan untuk langkah ini:

CharcoalCharcoal2 kg

Alatan diperlukan:

Long-Handled TongsLong-Handled Tongs
4

Twist the rod

While the rod is still hot and soft, clamp one end firmly (in a forked stick driven into the ground, or between two heavy stones). Grip the other end with tongs and twist slowly and evenly. Aim for about 1 full turn per 3 cm of length — tight enough to show a clear spiral pattern but not so tight that the rod kinks. Work quickly before the bronze cools and work-hardens. If it stiffens mid-twist, stop, re-anneal, and continue.
5

Straighten the twisted rod

Twisting often introduces slight bends and warps. While still warm, or after annealing again, lay the twisted rod on a flat surface and gently tap out any curves with a wooden mallet. The rod should lie flat and straight before bending into the torc shape. Rolling it under a flat board also helps straighten it.

Alatan diperlukan:

Wooden MalletWooden Mallet
6

Bend into a neck ring

Anneal the straightened twisted rod. Bend it gradually around a log or large stone of roughly head diameter (about 15-18 cm across) to form a C-shape. The opening should be about 3-4 cm — wide enough to slip over the neck from the front. Bend slowly and evenly to avoid kinking. The twist pattern should remain uniform around the curve.
7

Form the terminals

The two ends of the torc are the terminals — the most visible part when worn. For a simple torc, hammer each end flat and curl it outward into a small spiral using pliers or by bending around a narrow rod. For a more elaborate torc, hammer the ends into flat discs, or cast separate decorative knobs and attach them by wrapping with fine bronze wire.
8

Polish and finish

Rub the entire torc with fine sand on a leather pad to remove scale and oxidation from the annealing steps. Polish the twisted body to a bright golden sheen. Pay extra attention to the terminals. A final rub with animal fat protects the surface and gives it the warm glow seen in museum examples. The finished torc should spring slightly when the opening is pulled apart, then grip the neck when released.

Bahan untuk langkah ini:

Fine SandFine Sand50 g
Animal Fat (Tallow)Animal Fat (Tallow)20 g

Bahan

4

Alatan Diperlukan

4

Bahan Blueprint Bersambung

Blueprint berkaitan

Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

Hammering Bronze Sheet from a Cast Ingot — Raising and Planishingoleh Forge
Annealing and Cold-Working Bronze — Hardening Without a Forgeoleh Forge
Making a Clay Crucible for Smelting — The Vessel That Holds Molten Metaloleh Forge

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...