SENI

KECANTIKAN & KESEJAHTERAAN

KRAFTANGAN

BUDAYA & SEJARAH

HIBURAN

ALAM SEKITAR

MAKANAN & MINUMAN

KEJURUTERAAN TERBALIK

SAINS

SUKAN

TEKNOLOGI

BOLEH PAKAI

Controlling a Stepper Motor with an EasyDriver

Dicipta oleh

Martin

13. Julai 2026

Controlling a Stepper Motor with an EasyDriver

A stepper motor doesn't just spin — it moves in exact, repeatable steps, so you can command a precise angle with no position sensor at all. This motor takes 400 steps per revolution (0.9° per step). The EasyDriver board turns two simple Arduino signals — one pulse on STEP, one level on DIR — into the carefully sequenced coil currents a bipolar stepper needs. It's the same open-loop precision that drives 3D printers, CNC machines and camera sliders.

Pertengahan

1 hour

Arahan

Identify the two motor coils

A bipolar stepper has 4 wires — two coils of two wires each. Set a multimeter to continuity (or ohms) and find the pairs: the two wires that beep (low resistance) share a coil. Call them Coil A and Coil B. There is no polarity within a coil.

Bahan untuk langkah ini:

Motor langkah1 keping

Alatan diperlukan:

Digital Multimeter - Basic

Wire the driver, motor and power

Push the EasyDriver into the breadboard. Screw Coil A into the driver's A+/A- terminals and Coil B into B+/B-. Connect a 9 V battery to M+ and GND (motor power, 6–30 V). From the Arduino: D2 to STEP, D3 to DIR, D4 to MS1, D5 to MS2, D6 to ENABLE. IMPORTANT: also join Arduino GND to the EasyDriver GND so they share a ground.

Bahan untuk langkah ini:

Arduino Uno R31 keping

Pemacu motor langkah1 keping

Papan Roti1 keping

Wayar Pelompat1 bungkus

Pemegang bateri1 keping

Set the driver's current limit

The EasyDriver has a small potentiometer that limits coil current. With a small screwdriver, start it near the middle; once running, turn it down if the motor or chip gets hot, or up if the motor is weak or skips. Never exceed the motor's rated current — this board delivers up to 750 mA per phase.

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port. Leave the 9 V motor battery switched off until the sketch is uploaded.

Alatan diperlukan:

Komputer dengan Arduino IDE

Kabel USB-B

Upload the stepper sketch

Paste this sketch and upload, then switch on the battery. It turns the shaft one full revolution one way, pauses, and reverses — on a loop.

stepper_easydriver.inoarduino

// Drive a bipolar stepper with a SparkFun EasyDriver.
// Arduino -> EasyDriver:  D2=STEP, D3=DIR, D4=MS1, D5=MS2, D6=ENABLE (active LOW).
// Motor power (6-30V) on M+/GND; the Arduino and driver must share GND.
// Full-step mode (MS1=LOW, MS2=LOW): 400 STEP pulses = one revolution on this 400-step motor.

const int STEP_PIN = 2;
const int DIR_PIN  = 3;
const int MS1_PIN  = 4;
const int MS2_PIN  = 5;
const int EN_PIN   = 6;

const int STEPS_PER_REV = 400;   // full step, 0.9 deg per step

void setup() {
  pinMode(STEP_PIN, OUTPUT);
  pinMode(DIR_PIN, OUTPUT);
  pinMode(MS1_PIN, OUTPUT);
  pinMode(MS2_PIN, OUTPUT);
  pinMode(EN_PIN, OUTPUT);

  digitalWrite(MS1_PIN, LOW);   // MS1=LOW, MS2=LOW -> full step
  digitalWrite(MS2_PIN, LOW);
  digitalWrite(EN_PIN, LOW);    // LOW enables the driver outputs
}

void turnOneRevolution(bool clockwise) {
  digitalWrite(DIR_PIN, clockwise ? HIGH : LOW);
  for (int i = 0; i < STEPS_PER_REV; i++) {
    digitalWrite(STEP_PIN, HIGH);
    delay(2);                   // high time sets the speed
    digitalWrite(STEP_PIN, LOW);
    delay(2);
  }
}

void loop() {
  turnOneRevolution(true);    // one full turn clockwise
  delay(1000);
  turnOneRevolution(false);   // one full turn back
  delay(1000);
}

Test it

Switch on the 9 V battery. The shaft turns exactly one revolution one way, pauses a second, then one revolution back. In full-step mode this 400-step motor needs 400 STEP pulses per turn. If it only buzzes or vibrates without turning, a coil pair is split across the two channels — swap two wires so each coil sits on one channel (A or B).

Turn steps into precise motion

Steppers move an exact angle per pulse, so you can position with no feedback: to rotate a set angle, use steps = 400 × angle ÷ 360 (e.g. 100 steps = 90°). For smoother, quieter motion set MS1 and MS2 HIGH for 1/8 microstepping (3200 micro-steps per revolution). This precise, repeatable motion is exactly what drives 3D printers, CNC machines, camera sliders and robot joints.

Bahan

1
1
Motor langkah
1 keping
5 vendors sell this, none ship to you yet
Pemegang Tempat
2
2
Arduino Uno R3
1 keping
1 vendor sell this, none ship to you yet
Pemegang Tempat
2
2
Pemacu motor langkah
1 keping
2 vendors sell this, none ship to you yet
Pemegang Tempat
2
2
Papan Roti
1 keping
1 vendor sell this, none ship to you yet
Pemegang Tempat
2
2
Wayar Pelompat
1 bungkus
3 vendors sell this, none ship to you yet
Pemegang Tempat
2
2
Pemegang bateri
1 keping
14 vendors sell this, none ship to you yet
Pemegang Tempat

Alatan Diperlukan

1
1
Digital Multimeter - Basic10% komisen
Lihat
$14.24
4
4
Komputer dengan Arduino IDE
Pemegang Tempat
4
4
Kabel USB-B
1 vendor sell this, none ship to you yet
Pemegang Tempat

Blueprint berkaitan

Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

Controlling a DC Motor with an L298N Driver

oleh Ed

Pengenalan Robotik

BLUEPRINT NFT

Blinking LED — Your First Arduino Project

oleh Admiral OOM

Digital

575

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...