SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Coopered Vat: Oak Staves in Riveted Iron Hoops
Woody

Dicipta oleh

Woody

14. Oktober 2026NO
18
0
0
0
0

Coopered Vat: Oak Staves in Riveted Iron Hoops

A vat is the cooper's large open tub: oak staves standing edge to edge, held tight by hoops, with a flat bottom set in a groove. Coopers made the vats beer was brewed in; papermakers and chemists use them to hold pulp, washes and settling liquors. Shave tapered staves, forge and rivet iron hoops, raise the staves in the hoops and fit the bottom. The picture: our diagram, a vat and its tapered staves.
Lanjutan
Several days

Arahan

1

Shape the staves

Rive or saw oak into staves as long as the vat is deep. Shave each one on the horse, taper it from top to bottom (step 5 gives the widths), and plane the edges so neighbours meet along their whole length.

Bahan untuk langkah ini:

Papan kayu kerasPapan kayu keras6 keping

Alatan diperlukan:

Froe (pisau belah)Froe (pisau belah)
Bangku ketamBangku ketam
Pisau TarikPisau Tarik
Ketam tanganKetam tangan
Gergaji TanganGergaji Tangan
2

Forge the hoops

Draw wrought iron into flat strip about 30 × 3 mm (our size), cut it to the circumference where each hoop sits plus a lap, bend it round, punch the lap and rivet it closed.

Bahan untuk langkah ini:

Bar besi tempaBar besi tempa3 keping
Rivet besiRivet besi6 keping
ArangArang5 as required

Alatan diperlukan:

Relau tukang besiRelau tukang besi
AndasAndas
Tukul kepala baji lintangTukul kepala baji lintang
Penebuk panasPenebuk panas
Penyepit tukang besiPenyepit tukang besi
Sarung tangan kimpalanSarung tangan kimpalan
3

Raise the vat

Stand the staves inside a hoop, wide ends up, until the ring is closed. Drive the hoops down with a hammer and a block until the joints close tight.

Alatan diperlukan:

Tukul kepala baji lintangTukul kepala baji lintang
4

Groove and bottom

Cut a groove round the inside a little above the lower edge. Join planks into a board, scribe a circle to fit the groove, cut and bevel it, slack the lower hoop, spring the bottom in, and drive the hoop home. Fill with water: the wood swells and seals.

Bahan untuk langkah ini:

Papan kayu kerasPapan kayu keras2 keping

Alatan diperlukan:

Set pahatSet pahat
Jangka lukisJangka lukis
Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Tukul kepala baji lintangTukul kepala baji lintang
5

Staves and hoops

Memuatkan buku nota Jupyter…

Bahan

4
  • Pemegang Tempat
  • Pemegang Tempat
  • 6 keping
    Pemegang Tempat
  • 5 as required
    Pemegang Tempat

Alatan Diperlukan

13

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...