SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Cord-Wound Staff Churn Drive: A Swinging Lever Twists the Dash To and Fro by Cords
Lucius Leavenworth of Trumansburg, New York, received US 14,458, dated 18 March 1856, for "Machinery for Operating Churns": cords from a pulley, worked by a swinging lever, wind and unwind on the dash staff and turn it to and fro.
This rung prints the pulley, lever head, frame and dash, builds the drive on a churn and makes butter.
Pertengahan
About 4 hours, plus printing
Arahan
1
1
From a swing to a twist
From a swing to a twist
Memuatkan buku nota Jupyter…
2
2
A turned staff before it
A turned staff before it
Boyers turns his shaft with a crank; Leavenworth twists his with cords.
3
3
Read US 14,458
Read US 14,458
"By taking hold of the handle of the lever, and moving it with a reciprocating motion, the cords attached to arc of the lever, will alternately wind and unwind on the pulley F, causing it to partially revolve in the direction of the lever, thus causing the cords E, E, to move the staff with a reciprocating motion."
4
4
Print the parts
Print the parts
Print the pulley (/uploads/blueprints/cord-wound-staff-churn-drive-pulley.stl), the lever head (/uploads/blueprints/cord-wound-staff-churn-drive-lever-arc.stl), the frame (/uploads/blueprints/cord-wound-staff-churn-drive-frame.stl) and the dash (/uploads/blueprints/cord-wound-staff-churn-drive-dash.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Bahan untuk langkah ini:
Filamen PETG1 kepingAlatan diperlukan:
Pencetak 3D filamen (FDM)5
5
Post, frame and pulley
Post, frame and pulley
Stand a pine post beside a tapered food-grade bucket. Clamp the frame on its top, with a pine arm out over the bucket's centre carrying the pulley on a 10 mm rod. Pin the lever head on a 10 mm rod lower in the frame and glue a 12 mm dowel handle into it.
Bahan untuk langkah ini:
Papan pain1 keping
Baldi 20 Liter1 keping
Bar Bulat Keluli Lembut1 keping
Pasak kayu keras1 keping
Skru kayu #8 x 1"1 kepingAlatan diperlukan:
Gergaji Tangan
Gerudi Tanpa Wayar
Set Mata Gerudi
Set pemutar skru6
6
Staff, dash and cords
Staff, dash and cords
Push the dash onto a 16 mm hardwood staff and stand it in the bucket, its top in the pulley's large groove. Tie a cord from each pulley groove, wind it a few turns round the staff, the two the same way, and fix it to a pin in the staff. Tie cord H round the pulley's small hub in opposite directions to the two ends of the lever's arc.
Bahan untuk langkah ini:
Pasak kayu keras1 keping
Tali1 keping
Gam Kayu1 kepingAlatan diperlukan:
Gerudi Tanpa WayarSet Mata Gerudi7
7
The patent drawing
The patent drawing
US 14,458 drawing sheet, public domain (expired patent).
8
8
Churn
Churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 3 litres. Swing the lever steadily to and fro; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bahan untuk langkah ini:
Krim pekat3000 ml
Garam Laut Kasar1 keping
Air1 kepingAlatan diperlukan:
Termometer prob kekal
Jam Randik
Penimbang Dapur Digital
Mangkuk adun keluli tahan karat (besar)9
9
Troubleshooting
Troubleshooting
Cord-wound drive troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Lucius Leavenworth** of Trumansburg, Tompkins County, New York, US 14,458, 18 March 1856. The lever's wrist pin could take "a connecting rod from a rocking chain or other power." He claimed the cords attached to the pulley and wound on the staff to give a rotary motion. A bucket, pine and printed parts stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn.
Bahan
11- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 3000 mlPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Alatan Diperlukan
9- Pemegang Tempat
- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
Diagonal Screw Dasher Churn: Dished Blades on a Slanting Shaft Twist the Butter Together
oleh Hoop
Kerja Kayu
29
0
0
0
0
0
Rocking Two-Section Barrel Churn: Cream Falls Through a Grate as the Barrel Tips End Over End
oleh Karen
MAKANAN & MINUMAN
34
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
oleh TheChef
KRAFTANGAN
50
0
0
0
0
0
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.