SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
MASA DEPAN HIJAU
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
WEARABLES

Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments
Clay beads are among the oldest decorative objects made by humans — fired clay beads from Dolní Věstonice in the Czech Republic date to approximately 26,000 years ago, making them some of the earliest known ceramics. Unlike shell or bone beads that require drilling through hard material, clay beads are formed soft and pierced with a stick before firing, making them far easier to produce in quantity. Beads served as personal ornament, trade goods, counting tokens, and markers of social status across all prehistoric cultures. The process is simple: prepare clay, roll beads, pierce holes, dry, fire. The key challenge is preventing the beads from cracking during drying and firing — uniform thickness, thorough drying, and slow temperature increase are essential.
Pemula
2-3 hours (plus firing)
Arahan
1
1
Gather and Clean the Clay
Gather and Clean the Clay
Gather fine-grained clay and remove stones, roots, and debris by hand.
Bahan untuk langkah ini:
Raw Clay from Riverbank1 keping2
2
Knead the Clay Thoroughly
Knead the Clay Thoroughly
Knead the clay thoroughly to remove air bubbles — wedging on a flat stone works well.
3
3
Add Temper (Optional)
Add Temper (Optional)
Optionally mix in a small amount of fine sand (10-15%) as temper to reduce cracking.
4
4
Roll the Beads
Roll the Beads
Pinch off a small piece of clay and roll it between your palms into a smooth sphere (8-15mm diameter).
5
5
Pierce the Centre Hole
Pierce the Centre Hole
Pierce the centre of each bead with a thin stick, twig, or bone awl — push through from one side, then ream from both sides.
Alatan diperlukan:
Bone Awl6
6
Size the Hole for Cordage
Size the Hole for Cordage
The hole should be large enough for a cord (2-3mm diameter).
7
7
Leave the Stick in During Drying
Leave the Stick in During Drying
Leave the stick in place while drying to keep the hole open and prevent it from closing.
8
8
Dry Slowly in Shade
Dry Slowly in Shade
Set beads on a dry surface in shade and dry slowly for 2-3 days — fast drying causes cracks.
9
9
Remove the Sticks
Remove the Sticks
Remove the sticks once the clay is leather-hard.
10
10
Add Surface Decoration (Optional)
Add Surface Decoration (Optional)
Optional: press patterns into the bead surface with a pointed stick or stamp with cord impressions before drying.
11
11
Fire in a Pit Kiln
Fire in a Pit Kiln
Fire the beads in a pit kiln: place in the coals, cover with fuel, burn for 2-3 hours at 600-800°C, and allow to cool slowly in the ash.
Bahan
1- 1 kepingPemegang Tempat
Bahan Blueprint Bersambung
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.