SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI

Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
The Hights made the wings of a horizontal box-churn dash into a screw.
Cornelius R. Hight and John Hight of Geneva, Illinois, received US 7,490, dated 9 July 1850, for a "reacting spiral revolving dash" in a box churn: a shaft with four arms, those at one end at right angles to those at the other, and two wings fastened from arm to arm "so as to produce a quarter twist in the wings as they extend along the shaft." Its revolution produces "opposite currents, in the cream"; reversed, "the butter collects at the ends of the wings."
This rung works out the wings' pitch, then prints the dash in one piece, fits it in a box, and makes butter.
Pertengahan
About 3 hours, plus printing
Arahan
1
1
The quarter twist
The quarter twist
Memuatkan buku nota Jupyter…
2
2
Oblique wings on a horizontal arbor before it
Oblique wings on a horizontal arbor before it
The embedded blueprint sets straight wings at 30° to the axle. The Hights twist theirs a quarter turn from end to end, like a screw.
3
3
Read US 7,490
Read US 7,490
"The peculiar construction of the dash, consists in setting the arms to which the wings are attached, at right angles, upon opposite sides of the shaft, so as to produce a quarter twist in the wings as they extend along the shaft from one arm to the other."
4
4
Print the dash
Print the dash
Print the dash on end in one piece with supports (/uploads/blueprints/quarter-twist-spiral-dash-churn-dash.stl): shaft, four arms and two wings each twisted a quarter turn. Print the crank arm (/uploads/blueprints/quarter-twist-spiral-dash-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Bahan untuk langkah ini:
Filamen PETG1 kepingAlatan diperlukan:
Pencetak 3D filamen (FDM)5
5
Fit the box
Fit the box
Take a food-safe box about 220 × 150 × 160 mm, its proportions close to his 18 × 12 × 13 inches. Drill both ends on the axis 80 mm up. Push a 10 mm square hardwood shaft through one end, the dash and the other end, with a leather washer at each.
Bahan untuk langkah ini:
Bekas simpanan gred makanan1 keping
Pasak kayu keras1 keping
Jalur kulit1 kepingAlatan diperlukan:
Gerudi Tanpa Wayar
Set Mata Gerudi
Gergaji Tangan6
6
Crank and lid
Crank and lid
Glue the crank arm and a dowel handle on the shaft's outer end, and fit the box's lid, as his rabbeted cover.
Bahan untuk langkah ini:
Pasak kayu keras1 keping
Gam Kayu1 kepingAlatan diperlukan:
Kertas Pasir7
7
The patent drawing
The patent drawing
US 7,490 drawing sheet, public domain (expired patent).

8
8
Churn, then reverse to collect
Churn, then reverse to collect
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank steadily; time until the butter comes. Then reverse the crank so the butter collects at the ends of the wings, as they said. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bahan untuk langkah ini:
Krim pekat1500 ml
Garam Laut Kasar1 keping
Air1 kepingAlatan diperlukan:
Termometer prob kekal
Jam Randik
Penimbang Dapur Digital
Mangkuk adun keluli tahan karat (besar)9
9
Wings that scrape, butter that won't collect
Wings that scrape, butter that won't collect
Quarter-twist spiral dash troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Cornelius R. Hight and John Hight** of Geneva, Kane County, Illinois, received US 7,490, dated 9 July 1850. Their wings could be wood or tin, split into the arms with a saw and fastened with brads or small screws; the wing's inner border was cut to arcs of 16- and 23-inch circles; the dash ran on a coupling gudgeon in a cast box and a screw pivot. They wrote it made butter "in from 5 to 8 minutes"; that is their claim, not our measurement. They claimed the application of a reacting spiral revolving dash to a box churn or any of the usual forms of churns.
**Honest limits.** A food-safe box and a printed dash stand in for theirs, and our wings twist evenly rather than following their curved borders. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Bahan
8- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1500 mlPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
Alatan Diperlukan
9- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

Spiral-Vane Spring-Agitator Churn: Vanes That Snap Springs on the Bottom
oleh Martin
MAKANAN & MINUMAN
27
0
0
0
0
0

Oblique-Wing Reel Churn: Four Wings Across the Line of the Axle
oleh YourGrandma
MAKANAN & MINUMAN
17
0
0
0
0
0

Pass-Through Barrel Churn: A Twisted-Wing Dasher That Comes Out Whole Through a Hatch
oleh Woody
Kerja Kayu
32
0
0
0
0
0
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.
