Kerjasama
SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Safety Goggles: Soft Plastic Frame with Turnable Splash-Proof Vent Caps (Hirschmann, US 3,141,172, 1964)
Goggles that let air in but keep splashes out. A soft polyethylene frame seals on the face and holds one clear lens for both eyes. Four vents sit in the frame, each a short tube under a cup-shaped cap with holes on one side only. You turn each cap so its solid side faces the splash; air takes a winding path in, and any liquid that gets into a cap drains out of a hole at the bottom.
Result: ventilated safety goggles against liquids, chips and particles, with a lens you can replace.
Source: J. B. Hirschmann, US 3,141,172 (1964), with the frame and lens of his US 2,773,260 (1956). Unknown: sizes, the moulding, the strap. Picture: the patent drawing.
Pertengahan
Unknown
Arahan
1
1
Mould the frame
Mould the frame
Mould a one-piece goggle frame of a soft, light-transmitting plastic such as polyethylene. Give it a front rim with one opening for both eyes, narrower above the nose, and a nose pad moulded with the rim. Behind the rim, a wall runs back and ends in a flange that fits the face. Form a flange on the front of the rim to seat the lens, and short shoulders with sloping backs round the inside of the rim. Put a strap loop near the back edge on each side: a soft frame strapped at the front would be squeezed out of shape. Ours: LDPE. Not given: sizes, how it is moulded.
Bahan untuk langkah ini:
Pelet LDPE1 frameAlatan diperlukan:
Dimensi tidak diketahui2
2
Make the lens
Make the lens
Cut one lens from clear, flexible plastic such as cellulose acetate, shaped to match the rim, and pre-curve it to the shape it takes in the frame. Fit male snap fasteners (the 'Dot' type) to its edge strip above and below the nose part, and matching female ones in the rim flange. Not given: the thickness.
Bahan untuk langkah ini:
Kepingan plastik jernih1 lens
Kit butang tekan (tugas berat)1 2 pairsAlatan diperlukan:
GuntingDimensi tidak diketahui3
3
Make the four vents
Make the four vents
Mould each vent in two parts, of plastic or metal. The base is a short tube with a flange round its inner end; the cap is a cup that screws onto the tube (a press fit or solvent seal also serves), with a closed end and an outer flange. Through the cap's side, between the tube's end and the frame, make about three holes covering half the way round, and leave the other half solid. Not given: sizes.
Bahan untuk langkah ini:
Bahan tidak diketahui4 vent bases and capsAlatan diperlukan:
Dimensi tidak diketahui4
4
Assemble and set the caps
Assemble and set the caps
Make four holes in the frame wall: two at the top, two at the sides. Push each vent tube through from inside so its flange seals on the inside of the wall, and screw the cap on so its flange seals on the outside. Seat the lens against the rim flange, guided by the shoulders, and press the snaps home. Thread a head strap through the two loops. Before work, turn each cap so its solid side faces the expected splash, with one hole pointing down. Air then winds in under the cap and back down the tube; particles strike the walls and drop, and any liquid drains out of the lower hole. Not given: the strap material.
Bahan untuk langkah ini:
Bahan tidak diketahui1 head strapAlatan diperlukan:
Penebuk kertasBahan
4- 1 framePemegang Tempat
- 1 lensPemegang Tempat
- 1 2 pairsPemegang Tempat
- 1 head strapPemegang Tempat
Bahan Blueprint Bersambung
10% Atribusi
Chemical Splash Goggles: One Sealed Lens in a Moulded Rubber Frame (Hirschmann, 1954)
oleh Emma
Mekanik
5
0
0
0
1
0
Berbahaya
10% Atribusi
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
oleh Charlie
Industri
12
0
0
0
2
0
10% Atribusi
Plastic Sheet and Blown Film Extrusion
oleh Emma
Acuan Semperit
43
0
0
0
2
0
10% Atribusi
The Snap Fastener: A Spring That Pinches the Same Every Way
oleh Tex
Tekstil & Kulit
41
0
0
0
1
0
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.