SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Silver Solder from Fine Silver, Copper and Spelter: Gee, 1877
Silver solder joins silver, copper and brass with a strong, hard seam. The silversmith George Gee preferred one made of fine silver, shot copper and a little spelter (zinc), melted only once: his best hard solder is 16 dwt of fine silver, 3 dwt 12 gr of shot copper and 12 gr of spelter to the ounce, about 80, 17.5 and 2.5 per cent. More copper and zinc make it flow sooner (his medium, easy and common solders). Silver and copper alone give the hardest, least fusible solder; too much zinc makes it eat away during soldering.
Pertengahan
Two hours
Arahan
1
1
Weigh the metals
Weigh the metals
Memuatkan buku nota Jupyter…
Bahan untuk langkah ini:
Perak Halus80 g
Jongkong Tembaga17.5 g
Jongkong Zink2.5 gAlatan diperlukan:
Penimbang
Pahat besi sejuk2
2
Anneal and test the crucible
Anneal and test the crucible
Before a new plumbago (graphite) crucible is charged, heat it slowly to redness on a fire that is dying down and has no blaze, so it does not crack. Touch it with a cold iron bar: if cracks show, reject it.
Alatan diperlukan:
Mangkuk pijar grafit-tanah liat
Relau Arang
Penyepit Mangkuk Pijar3
3
Melt silver and copper
Melt silver and copper
Put the copper at the bottom of the crucible, the silver on top, and melt them in the furnace. Stir them well together with an iron stirrer, tapered at the point and first heated to redness. When the metals are just beginning to fuse, cover the melt with finely divided, pure charcoal to keep the air off it.
Bahan untuk langkah ini:
Arang - hancur halus1 as requiredAlatan diperlukan:
Relau Arang
Pengacau besi
Sarung Tangan Tahan Haba4
4
Add the spelter
Add the spelter
Hold the spelter in a long pair of tongs over the mouth of the crucible, inside the furnace, until it has almost reached its melting point, then drop it into the molten metal and stir quickly so it mixes in. Zinc burns away quickly in the air, so it goes in last.
Alatan diperlukan:
PenyepitPengacau besiSarung Tangan Tahan Haba5
5
Pour the ingot
Pour the ingot
Withdraw the crucible from the furnace at once and pour into an ingot mould that is clean, smooth, lightly greased, dusted with fine charcoal and warmed: a cold mould makes the metal spout, but do not overheat it either. Melt solder only once; Gee found that solders containing volatile metals grow hard, brittle and drossy with repeated melting.
Bahan untuk langkah ini:
Arang - hancur halus1 as requiredAlatan diperlukan:
Penyepit Mangkuk Pijar
Acuan jongkongSarung Tangan Tahan Haba6
6
Roll into pallions or file to dust
Roll into pallions or file to dust
Roll the solder out thin between flattening rollers and cut it lengthways and then crossways with hand shears into little bits (pallions), or file it into fine dust, according to the work in hand. The work is then bound together, wetted with a paste of borax and water, and the pallions laid on the joints and melted with a blowpipe flame.
Alatan diperlukan:
Kilang gelek logam
Sepit pemotong logam
Kikir (Kikir Tangan)Bahan
4- 80 gPemegang Tempat
- 17.5 gPemegang Tempat
- 2.5 gPemegang Tempat
- 1 as requiredPemegang Tempat
Alatan Diperlukan
12- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip
Berbahaya
Extracting Silver by Cupellation — Separating Noble Metal from Lead Ore
oleh Peter
Kerja Logam
70
0
0
0
2
0
Smelting Copper from Malachite — From Green Ore to Red Metal
oleh Peter
Kerja Logam
106
0
0
0
10
0
Extracting Zinc from Sphalerite — Roasting and Reduction of the Invisible Metal
oleh Peter
Kerja Logam
78
0
0
0
8
0
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.