SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
A plunger pressed straight down by the hand needs a strong push to empty a lemon.
A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger."
This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Pertengahan
About 5 hours
Arahan
1
1
The cam's force
The cam's force
Memuatkan buku nota Jupyter…
2
2
A lever press before it
A lever press before it
The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3
3
Read US 165,638
Read US 165,638
"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E."
"When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4
4
Build the squeezer and press lemons
Build the squeezer and press lemons
**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole.
**Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl.
**Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin.
**Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised.
**Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.
Bahan untuk langkah ini:
Papan Kayu Keras2 keping
Blok Kayu Keras2 keping
Pasak kayu0.6 meter
Skru kayu16 keping
Gam Kayu1 keping
Tin1 keping
Engsel daun1 keping
Bar Bulat Keluli Lembut0.2 meter
Paku2 keping
Spring tarik2 keping
Lemon3 kepingAlatan diperlukan:
Gergaji Tangan
Set pahat kayu
Kikir kasar
Gerudi Tanpa Wayar
Set Mata Gerudi
Gunting kepingan logam
Tukul
Set pemutar skru
Gergaji Besi
Pisau dapur
Penimbang Dapur Digital
Sarung Tangan Kerja Kulit5
5
A cam that slips, jams or does not lift
A cam that slips, jams or does not lift
Cam-lever lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever.
**Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.
Bahan
11- 2 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 0.6 meterPemegang Tempat
- 16 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 1 kepingPemegang Tempat
- 0.2 meterPemegang Tempat
- 2 kepingPemegang Tempat
- 2 kepingPemegang Tempat
- 3 kepingPemegang Tempat
Alatan Diperlukan
12- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- 1 vendor sell this, none ship to you yetPemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
- Pemegang Tempat
Blueprint ini membuat
Blueprint berkaitan
Blueprint ini berkongsi pengetahuan — teknik, bahan atau prinsip

The Ring-Set Lemon Squeezer: A Bowl Held in Its Handle by a Screwed Ring
oleh YourGrandma
Kerja Kayu
39
0
0
0
0
0

The False-Bottom Lemon Press: A Hinged Lever Over a Die, and One Hole for the Juice
oleh TheChef
Kerja Kayu
32
0
0
0
0
0

The Clamp-Frame Lemon Squeezer: A Screw Press That Clamps to the Table
oleh Forge
Kerja Logam
30
0
0
0
0
0
CC0 Domain Awam
Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.
Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.
