SENI
KECANTIKAN & KESEJAHTERAAN
KRAFTANGAN
BUDAYA & SEJARAH
HIBURAN
ALAM SEKITAR
MAKANAN & MINUMAN
KEJURUTERAAN TERBALIK
SAINS
SUKAN
TEKNOLOGI
BOLEH PAKAI
Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads
Woody

Dicipta oleh

Woody

14. Oktober 2026NO
15
0
0
0
0

Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads

A barrel is the cooper's closed vessel: oak staves held by hoops, bulging at the middle, with flat heads set in grooves at both ends. Coopers heat the staves to bend them. Shape staves wider at the middle than the ends, raise them in a hoop, heat them over a small fire and draw the open end together, drive the hoops, and fit the heads. The picture: a new oak barrel in a cooper's workshop, with iron hoops on the floor.
Lanjutan
Several days

Arahan

1

Shape the staves

Rive and shave oak staves as for the vat, but taper each from the middle toward both ends, and hollow the inside face a little.

Bahan untuk langkah ini:

Papan kayu kerasPapan kayu keras8 keping

Alatan diperlukan:

Froe (pisau belah)Froe (pisau belah)
Bangku ketamBangku ketam
Pisau TarikPisau Tarik
Ketam tanganKetam tangan
2

Raise and fire

Stand the staves inside one hoop to form a skirt. Light a small charcoal fire inside, wet the outside, and as the staves warm, draw the open end together with a rope round it until a hoop can be driven on.

Bahan untuk langkah ini:

ArangArang3 as required
AirAir10 liter

Alatan diperlukan:

Simpai besiSimpai besi
Tali temali kuatTali temali kuat
Tukul kepala baji lintangTukul kepala baji lintang
Sarung Tangan Tahan HabaSarung Tangan Tahan Haba
3

Hoops

Drive the rest of the iron hoops on, two near each end and two at the quarters, until the joints close tight.

Bahan untuk langkah ini:

Simpai besiSimpai besi6 keping

Alatan diperlukan:

Tukul kepala baji lintangTukul kepala baji lintang
4

Ends and grooves

Level the ends and bevel the inside edge with the adze, then cut a groove round the inside near each end.

Alatan diperlukan:

BeliungBeliung
Set pahatSet pahat
5

Heads and bung

Join planks into two boards, scribe circles to fit the grooves, cut and bevel them, slack the end hoops and spring the heads in. Bore a bung hole in the middle stave. Fill with water to swell it tight.

Bahan untuk langkah ini:

Papan kayu kerasPapan kayu keras2 keping
AirAir50 liter

Alatan diperlukan:

Jangka lukisJangka lukis
Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Tukul kepala baji lintangTukul kepala baji lintang
Gerimit tanganGerimit tangan
6

Capacity of a barrel

Memuatkan buku nota Jupyter…

Bahan

4
  • Pemegang Tempat
  • 3 as required
    Pemegang Tempat
  • 60 liter
    Pemegang Tempat
  • 6 keping
    Pemegang Tempat

Alatan Diperlukan

13

CC0 Domain Awam

Blueprint ini dikeluarkan di bawah CC0. Anda bebas menyalin, mengubah, mengedar, dan menggunakan karya ini untuk sebarang tujuan, tanpa meminta kebenaran.

Sokong Pembuat dengan membeli produk melalui Blueprint mereka di mana mereka memperoleh Komisen Pembuat ditetapkan oleh Penjual, atau cipta iterasi baru Blueprint ini dan sertakan ia sebagai sambungan dalam Blueprint anda sendiri untuk berkongsi hasil.

Perbincangan

(0)

Log masuk untuk menyertai perbincangan

Memuatkan komen...