IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Youblob · CC0
Drying Stickers Riven from a Seasoned Log
Stickers are the small dry strips laid between layers of stacked boards so air can flow through the pile as it dries. The first stack needs stickers before there are any boards, so rive them straight from a seasoned log with froe and mallet and plane them square.
The picture: our diagram of a stickered stack.
Olùbẹ̀rẹ̀
Two hours
Ìlànà
1
1
Cut a billet
Cut a billet
Saw a straight-grained length off a seasoned log, a little longer than your stack is wide.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Igi líle tí a ti gbẹ1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Ọwọ́
Ìdíwọ̀n2
2
Rive it
Rive it
Split the billet in halves, then halves again, with froe and mallet, following the grain, until the pieces are a little over 2 cm square.
Àwọn irinṣẹ́ tí a nílò:
Froe (ọ̀bẹ ìpín)
Òòlù Igi
Ìbọ̀wọ́ Iṣẹ́ Awọ3
3
Plane them even
Plane them even
Plane each stick to the same thickness, about 2 cm, so every layer of the stack lies flat.
Àwọn irinṣẹ́ tí a nílò:
Ohun èlò ìfárí igi (pìlánì)Ìdíwọ̀n4
4
Stickers for a stack
Stickers for a stack
Ń ṣí ìwé Jupyter…
Àwọn ohun-èlò
1- 1 ẹyọÀyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.