IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Hardwood Strips Ripped and Planed from a Board
Hardwood strips for dashers, rulers and glued-up boards are ripped from a dry board along the grain and planed square. Gauge the lines first, saw on the waste side, then plane down to the line.
The picture: holding a wooden plane, from Otto Salomon's Teacher's Handbook of Slöjd (1900).
Olùbẹ̀rẹ̀
An hour or two
Ìlànà
1
1
Choose and true the board
Choose and true the board
Pick a dry, straight-grained board. Plane one edge straight and square to the face; all strips are measured from it.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Pátákó Igi Líle1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ohun èlò ìfárí igi (pìlánì)
Igun-òsùwọ̀n tí ó dúró
Ìdìmú Tábìlì2
2
Gauge the strips
Gauge the strips
Set the marking gauge to the strip width and score a line along both faces from the trued edge.
Àwọn irinṣẹ́ tí a nílò:
Ohun èlò ìsàmì3
3
Rip along the grain
Rip along the grain
Clamp the board and rip just on the waste side of the line with the rip saw.
Àwọn irinṣẹ́ tí a nílò:
Ayùn gígé bá ìhà igi
Àwọn clamp4
4
Plane to the line
Plane to the line
Plane the sawn edge down to the gauge line and check it square. Re-true the board's edge and gauge the next strip.
Àwọn irinṣẹ́ tí a nílò:
Ohun èlò ìfárí igi (pìlánì)Igun-òsùwọ̀n tí ó dúróÌdìmú Tábìlì
Òṣùwọ̀n Kálípà Díjítà Ìnṣì 65
5
Strips per board
Strips per board
Ń ṣí ìwé Jupyter…
Àwọn ohun-èlò
1- 1 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
7- Àyè
- Àyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.